EDIT 2017-01-07 I was able to brick another board. I think that the programmer is the cause.

I tried to upload bootloader with fuses from arduino and it failed with verification error.

I was able to burn bootloader from command line after seting fuses and restarting the board.

When I tried to upload the program it I got

avrdude: verifying ...
avrdude: verification error, first mismatch at byte 0x0000
         0x00 != 0x0c
avrdude: verification error; content mismatch

avrdude: safemode: lfuse reads as 0
avrdude: safemode: hfuse reads as 0
avrdude: safemode: efuse reads as 0
avrdude: safemode: lfuse changed! Was 62, and is now 0
Would you like this fuse to be changed back? [y/n] n
avrdude: safemode: hfuse changed! Was da, and is now 0
Would you like this fuse to be changed back? [y/n] n
avrdude: safemode: efuse changed! Was 7, and is now 0
Would you like this fuse to be changed back? [y/n] n
avrdude: safemode: Fuses OK (H:07, E:DA, L:62)

I answered yes because in in earlier attempts it just froze.

Now the board is in same condition as the first one.

Is it possible to revive it? Thanks.

Recently I have been experimenting with battery powered sensor (mySensors).

I created node with 3.3V Arduino Pro Mini (ATMega328P @ 8Mhz with nordic radio chip and BME280 sensor) and successfully programed it many times using either USBAsp programmer or serial (to USB) programmer.

I wanted to lower power consumption and so I disconnected power led and burned fuses as follows: lfuse 62 hfuse DA efuse 7

It worked successfully and I recompiled the sketch and upload it with USBasp. I got an error that data cant be verified. It was late in the night so I jumped to Internet and googled it. In one forum I found, post (which I am unable to find again) that stated the he was able to upload sketch when he switched programmer to 5V. (Power was connected to Vcc)

I did that and it worked fine.

Than I tried to make change to sketch and upload it again (on 3,3V) and again got verification error so I unplugged programmer and switched back to 5V.

When I did that, the device stopped answering.

I regularly used this command to check that device responds and see fuses

avrdude.exe -C"C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf" -v -patmega328p -cusbasp -Pusb

What i did

1. Checked wiring.

2. Tried program fuses on blank new arduino - worked (programmer is fine)

3. Measured voltage ok

4. Measured current (its around 4mA, I see it as the board is not sleeping and is actively doing something)

5. I noticed that when I issue command mentioned above the on board led quickly lights up and then goes off again.

6. I tried to power it from raw, from Vcc and from Vcc on serial hader (picture).

7. I measured power on Vcc when connected to Raw pin and it reads 3.3V so power regulator should be ok.

My question is

1. Is it possible that I burned the ATMega chip?
2. Is it possible that I see target not answering because of USBAsp is unable to lower programming frequency? (warning: cannot set sck period. please check for usbasp firmware update.)

Please suggest if there is anything I can try before throwing it out.

Thank you.

Recently I have been experimenting with battery powered sensor (mySensors).

I created node with 3.3V Arduino Pro Mini (ATMega328P @ 8Mhz with nordic radio chip and BME280 sensor) and successfully programed it many times using either USBAsp programmer or serial (to USB) programmer.

I wanted to lower power consumption and so I disconnected power led and burned fuses as follows: lfuse 62 hfuse DA efuse 7

It worked successfully and I recompiled the sketch and upload it with USBasp. I got an error that data cant be verified. It was late in the night so I jumped to Internet and googled it. In one forum I found, post (which I am unable to find again) that stated the he was able to upload sketch when he switched programmer to 5V. (Power was connected to Vcc)

I did that and it worked fine.

Than I tried to make change to sketch and upload it again (on 3,3V) and again got verification error so I unplugged programmer and switched back to 5V.

When I did that, the device stopped answering.

I regularly used this command to check that device responds and see fuses

avrdude.exe -C"C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf" -v -patmega328p -cusbasp -Pusb

What i did

1. Checked wiring.

2. Tried program fuses on blank new arduino - worked (programmer is fine)

3. Measured voltage ok

4. Measured current (its around 4mA, I see it as the board is not sleeping and is actively doing something)

5. I noticed that when I issue command mentioned above the on board led quickly lights up and then goes off again.

6. I tried to power it from raw, from Vcc and from Vcc on serial hader (picture).

7. I measured power on Vcc when connected to Raw pin and it reads 3.3V so power regulator should be ok.

8. I used -B10 switch to averdude with no luck

My question is

1. Is it possible that I burned the ATMega chip?
2. Is it possible that I see target not answering because of USBAsp is unable to lower programming frequency? (warning: cannot set sck period. please check for usbasp firmware update.)

Please suggest if there is anything I can try before throwing it out.

Thank you.