| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull networking fixes from David Miller:
1) Handle max TX power properly wrt VIFs and the MAC in iwlwifi, from
Avri Altman.
2) Use the correct FW API for scan completions in iwlwifi, from Avraham
Stern.
3) FW monitor in iwlwifi accidently uses unmapped memory, fix from Liad
Kaufman.
4) rhashtable conversion of mac80211 station table was buggy, the
virtual interface was not taken into account. Fix from Johannes
Berg.
5) Fix deadlock in rtlwifi by not using a zero timeout for
usb_control_msg(), from Larry Finger.
6) Update reordering state before calculating loss detection, from
Yuchung Cheng.
7) Fix off by one in bluetooth firmward parsing, from Dan Carpenter.
8) Fix extended frame handling in xiling_can driver, from Jeppe
Ledet-Pedersen.
9) Fix CODEL packet scheduler behavior in the presence of TSO packets,
from Eric Dumazet.
10) Fix NAPI budget testing in fm10k driver, from Alexander Duyck.
11) macvlan needs to propagate promisc settings down the the lower
device, from Vlad Yasevich.
12) igb driver can oops when changing number of rings, from Toshiaki
Makita.
13) Source specific default routes not handled properly in ipv6, from
Markus Stenberg.
14) Use after free in tc_ctl_tfilter(), from WANG Cong.
15) Use softirq spinlocking in netxen driver, from Tony Camuso.
16) Two ARM bpf JIT fixes from Nicolas Schichan.
17) Handle MSG_DONTWAIT properly in ring based AF_PACKET sends, from
Mathias Kretschmer.
18) Fix x86 bpf JIT implementation of FROM_{BE16,LE16,LE32}, from Alexei
Starovoitov.
19) ll_temac driver DMA maps TX packet header with incorrect length, fix
from Michal Simek.
20) We removed pm_qos bits from netdevice.h, but some indirect
references remained. Kill them. From David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
net: Remove remaining remnants of pm_qos from netdevice.h
e1000e: Add pm_qos header
net: phy: micrel: Fix regression in kszphy_probe
net: ll_temac: Fix DMA map size bug
x86: bpf_jit: fix FROM_BE16 and FROM_LE16/32 instructions
netns: return RTM_NEWNSID instead of RTM_GETNSID on a get
Update be2net maintainers' email addresses
net_sched: gred: use correct backlog value in WRED mode
pppoe: drop pppoe device in pppoe_unbind_sock_work
net: qca_spi: Fix possible race during probe
net: mdio-gpio: Allow for unspecified bus id
af_packet / TX_RING not fully non-blocking (w/ MSG_DONTWAIT).
bnx2x: limit fw delay in kdump to 5s after boot
ARM: net: delegate filter to kernel interpreter when imm_offset() return value can't fit into 12bits.
ARM: net fix emit_udiv() for BPF_ALU | BPF_DIV | BPF_K intruction.
mpls: Change reserved label names to be consistent with netbsd
usbnet: avoid integer overflow in start_xmit
netxen_nic: use spin_[un]lock_bh around tx_clean_lock (2)
net: xgene_enet: Set hardware dependency
net: amd-xgbe: Add hardware dependency
...
|
|
Usually, RTM_NEWxxx is returned on a get (same as a dump).
Fixes: 0c7aecd4bde4 ("netns: add rtnl cmd to add and get peer netns ids")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In WRED mode, the backlog for a single virtual queue (VQ) should not be
used to determine queue behavior; instead the backlog is summed across
all VQs. This sum is currently used when calculating the average queue
lengths. It also needs to be used when determining if the queue's hard
limit has been reached, or when reporting each VQ's backlog via netlink.
q->backlog will only be used if the queue switches out of WRED mode.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes an issue where the send(MSG_DONTWAIT) call
on a TX_RING is not fully non-blocking in cases where the device's sndBuf is
full. We pass nonblock=true to sock_alloc_send_skb() and return any possibly
occuring error code (most likely EGAIN) to the caller. As the fast-path stays
as it is, we keep the unlikely() around skb == NULL.
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since these are now visible to userspace it is nice to be consistent
with BSD (sys/netmpls/mpls.h in netBSD).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When tcf_destroy() returns true, tp could be already destroyed,
we should not use tp->next after that.
For long term, we probably should move tp list to list_head.
Fixes: 1e052be69d04 ("net_sched: destroy proto tp when all filters are gone")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the peer of an RDS-TCP connection restarts, a reconnect
attempt should only be made from the active side of the TCP
connection, i.e. the side that has a transient TCP port
number. Do not add the passive side of the TCP connection
to the c_hash_node and thus avoid triggering rds_queue_reconnect()
for passive rds connections.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running RDS over TCP, the active (client) side connects to the
listening ("passive") side at the RDS_TCP_PORT. After the connection
is established, if the client side reboots (potentially without even
sending a FIN) the server still has a TCP socket in the esablished
state. If the server-side now gets a new SYN comes from the client
with a different client port, TCP will create a new socket-pair, but
the RDS layer will incorrectly pull up the old rds_connection (which
is still associated with the stale t_sock and RDS socket state).
This patch corrects this behavior by having rds_tcp_accept_one()
always create a new connection for an incoming TCP SYN.
The rds and tcp state associated with the old socket-pair is cleaned
up via the rds_tcp_state_change() callback which would typically be
invoked in most cases when the client-TCP sends a FIN on TCP restart,
triggering a transition to CLOSE_WAIT state. In the rarer event of client
death without a FIN, TCP_KEEPALIVE probes on the socket will detect
the stale socket, and the TCP transition to CLOSE state will trigger
the RDS state cleanup.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If there are only IPv6 source specific default routes present, the
host gets -ENETUNREACH on e.g. connect() because ip6_dst_lookup_tail
calls ip6_route_output first, and given source address any, it fails,
and ip6_route_get_saddr is never called.
The change is to use the ip6_route_get_saddr, even if the initial
ip6_route_output fails, and then doing ip6_route_output _again_ after
we have appropriate source address available.
Note that this is '99% fix' to the problem; a correct fix would be to
do route lookups only within addrconf.c when picking a source address,
and never call ip6_route_output before source address has been
populated.
Signed-off-by: Markus Stenberg <markus.stenberg@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
Here are a couple of important Bluetooth & mac802154 fixes for 4.1:
- mac802154 fix for crypto algorithm allocation failure checking
- mac802154 wpan phy leak fix for error code path
- Fix for not calling Bluetooth shutdown() if interface is not up
Let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I forgot to update tcp_westwood when changing get_info() behavior,
this patch should fix this.
Fixes: 64f40ff5bbdb ("tcp: prepare CC get_info() access from getsockopt()")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move to include/uapi/linux/mpls.h to be externally visibile.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
We have only a few fixes right now:
* a fix for an issue with hash collision handling in the
rhashtable conversion
* a merge issue - rhashtable removed default shrinking
just before mac80211 was converted, so enable it now
* remove an invalid WARN that can trigger with legitimate
userspace behaviour
* add a struct member missing from kernel-doc that caused
a lot of warnings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-05-04
Here's the first bluetooth-next pull request for 4.2:
- Various fixes for at86rf230 driver
- ieee802154: trace events support for rdev->ops
- HCI UART driver refactoring
- New Realtek IDs added to btusb driver
- Off-by-one fix for rtl8723b in btusb driver
- Refactoring of btbcm driver for both UART & USB use
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
c0adf54a109 introduced new sparse warnings:
CHECK /home/dahern/kernels/linux.git/net/rds/ib_cm.c
net/rds/ib_cm.c:191:34: warning: incorrect type in initializer (different base types)
net/rds/ib_cm.c:191:34: expected unsigned long long [unsigned] [usertype] dp_ack_seq
net/rds/ib_cm.c:191:34: got restricted __be64 <noident>
net/rds/ib_cm.c:194:51: warning: cast to restricted __be64
The temporary variable for sequence number should have been declared as __be64
rather than u64. Make it so.
Signed-off-by: David Ahern <david.ahern@oracle.com>
Cc: shamir rabinovitch <shamir.rabinovitch@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code in __netdev_upper_dev_link() has an over-stringent
loop detection logic that actually prevents valid configurations
from working correctly.
In particular, the logic returns an error if an upper device
is already in the list of all upper devices for a given dev.
This particular check seems to be a overzealous as it disallows
perfectly valid configurations. For example:
# ip l a link eth0 name eth0.10 type vlan id 10
# ip l a dev br0 typ bridge
# ip l s eth0.10 master br0
# ip l s eth0 master br0 <--- Will fail
If you switch the last two commands (add eth0 first), then both
will succeed. If after that, you remove eth0 and try to re-add
it, it will fail!
It appears to be enough to simply check adj_list to keeps things
safe.
I've tried stacking multiple devices multiple times in all different
combinations, and either rx_handler registration prevented the stacking
of the device linking cought the error.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In an environment where the KDC is running Active Directory, the
exported composite name field returned in the context could be large
enough to span a page boundary. Attaching a scratch buffer to the
decoding xdr_stream helps deal with those cases.
The case where we saw this was actually due to behavior that's been
fixed in newer gss-proxy versions, but we're fixing it here too.
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Simo Sorce <simo@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
This reverts commit c243d7e20996254f89c28d4838b5feca735c030d.
That patch is solving a non-existant problem while creating a
real problem. Just because a socket is allocated in the init
name space doesn't mean that it gets hashed in the init name space.
When we unhash it the name space must be the same as the one
we had when we hashed it. So this patch is completely bogus
and causes socket leaks.
Reported-by: Andrey Wagin <avagin@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rdma_conn_param private data is copied using memcpy after headers such
as cma_hdr (see cma_resolve_ib_udp as example). so the start of the
private data is aligned to the end of the structure that come before. if
this structure end with u32 the meaning is that the start of the private
data will be 4 bytes aligned. structures that use u8/u16/u32/u64 are
naturally aligned but in case the structure start is not 8 bytes aligned,
all u64 members of this structure will not be aligned. to solve this issue
we must use special macros that allow unaligned access to those
unaligned members.
Addresses the following kernel log seen when attempting to use RDMA:
Kernel unaligned access at TPC[10507a88] rds_ib_cm_connect_complete+0x1bc/0x1e0 [rds_rdma]
Acked-by: Chien Yen <chien.yen@oracle.com>
Signed-off-by: shamir rabinovitch <shamir.rabinovitch@oracle.com>
[Minor tweaks for top of tree by:]
Signed-off-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently limit the hash table size to 64K which is very bad
as even 10 years ago it was relatively easy to generate millions
of sockets.
Since the hash table is naturally limited by memory allocation
failure, we don't really need an explicit limit so this patch
removes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Thomas Graf <tgraf@noironetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under presence of TSO/GSO/GRO packets, codel at low rates can be quite
useless. In following example, not a single packet was ever dropped,
while average delay in codel queue is ~100 ms !
qdisc codel 0: parent 1:12 limit 16000p target 5.0ms interval 100.0ms
Sent 134376498 bytes 88797 pkt (dropped 0, overlimits 0 requeues 0)
backlog 13626b 3p requeues 0
count 0 lastcount 0 ldelay 96.9ms drop_next 0us
maxpacket 9084 ecn_mark 0 drop_overlimit 0
This comes from a confusion of what should be the minimal backlog. It is
pretty clear it is not 64KB or whatever max GSO packet ever reached the
qdisc.
codel intent was to use MTU of the device.
After the fix, we finally drop some packets, and rtt/cwnd of my single
TCP flow are meeting our expectations.
qdisc codel 0: parent 1:12 limit 16000p target 5.0ms interval 100.0ms
Sent 102798497 bytes 67912 pkt (dropped 1365, overlimits 0 requeues 0)
backlog 6056b 3p requeues 0
count 1 lastcount 1 ldelay 36.3ms drop_next 0us
maxpacket 10598 ecn_mark 0 drop_overlimit 0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kathleen Nichols <nichols@pollere.com>
Cc: Dave Taht <dave.taht@gmail.com>
Cc: Van Jacobson <vanj@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we don't do that, then the poison value is left in the ->pprev
backlink.
This can cause crashes if we do a disconnect, followed by a connect().
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Wen Xu <hotdog3645@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fix endian convertions for extended address and short address
handling when TP_printk is called.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This code is based on commit 6bab2e19c5ffd
("cfg80211: pass name_assign_type to rdev_add_virtual_intf()")
This will expose in sysfs whether the ifname of a IEEE-802.15.4
device is set by userspace or generated by the kernel.
We are using two types of name_assign_types
o NET_NAME_ENUM: Default interface name provided by kernel
o NET_NAME_USER: Interface name provided by user.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Enabling tracing via
echo 1 > /sys/kernel/debug/tracing/events/cfg802154/enable
enables event tracing like
iwpan dev wpan0 set pan_id 0xbeef
cat /sys/kernel/debug/tracing/trace
# tracer: nop
#
# entries-in-buffer/entries-written: 2/2 #P:1
#
# _-----=> irqs-off
# / _----=> need-resched
# | / _---=> hardirq/softirq
# || / _--=> preempt-depth
# ||| / delay
# TASK-PID CPU# |||| TIMESTAMP FUNCTION
# | | | |||| | |
iwpan-2663 [000] .... 170.369142: 802154_rdev_set_pan_id: phy0, wpan_dev(1), pan id: 0xbeef
iwpan-2663 [000] .... 170.369177: 802154_rdev_return_int: phy0, returned: 0
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In case of error, the functions crypto_alloc_aead() and crypto_alloc_blkcipher()
returns ERR_PTR() and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Currently if ieee802154_if_add failed, we don't unregister the wpan phy
which was registered before. This patch adds a correct error handling
for unregister the wpan phy when ieee802154_if_add failed.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Most likely, the shutdown routine requires the interface to be up.
This is the case for BTUSB_INTEL: the routine tries to send a command
to the interface, but since this one is down, it fails and exits once
HCI_INIT_TIMEOUT has expired.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.0.x
|
|
tcp_mark_lost_retrans is not used when FACK is disabled. Since
tcp_update_reordering may disable FACK, it should be called first
before tcp_mark_lost_retrans.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Congestion Control modules can provide per flow information,
but current way to get this information is to use netlink.
Like TCP_INFO, let's add TCP_CC_INFO so that applications can
issue a getsockopt() if they have a socket file descriptor,
instead of playing complex netlink games.
Sample usage would be :
union tcp_cc_info info;
socklen_t len = sizeof(info);
if (getsockopt(fd, SOL_TCP, TCP_CC_INFO, &info, &len) == -1)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We would like that optional info provided by Congestion Control
modules using netlink can also be read using getsockopt()
This patch changes get_info() to put this information in a buffer,
instead of skb, like tcp_get_info(), so that following patch
can reuse this common infrastructure.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch tracks total number of payload bytes received on a TCP socket.
This is the sum of all changes done to tp->rcv_nxt
RFC4898 named this : tcpEStatsAppHCThruOctetsReceived
This is a 64bit field, and can be fetched both from TCP_INFO
getsockopt() if one has a handle on a TCP socket, or from inet_diag
netlink facility (iproute2/ss patch will follow)
Note that tp->bytes_received was placed near tp->rcv_nxt for
best data locality and minimal performance impact.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Eric Salo <salo@google.com>
Cc: Martin Lau <kafai@fb.com>
Cc: Chris Rapier <rapier@psc.edu>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch tracks total number of bytes acked for a TCP socket.
This is the sum of all changes done to tp->snd_una, and allows
for precise tracking of delivered data.
RFC4898 named this : tcpEStatsAppHCThruOctetsAcked
This is a 64bit field, and can be fetched both from TCP_INFO
getsockopt() if one has a handle on a TCP socket, or from inet_diag
netlink facility (iproute2/ss patch will follow)
Note that tp->bytes_acked was placed near tp->snd_una for
best data locality and minimal performance impact.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Eric Salo <salo@google.com>
Cc: Martin Lau <kafai@fb.com>
Cc: Chris Rapier <rapier@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
eeprom-length is a switch property, not a dsa property, and thus
needs to be attached to the switch node, not to the dsa node.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 6793abb4e849 ("net: dsa: Add support for switch EEPROM access")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, we try to accumulate arrived packets in the links's
'deferred' queue during the parallel link syncronization phase.
This entails two problems:
- With an unlucky combination of arriving packets the algorithm
may go into a lockstep with the out-of-sequence handling function,
where the synch mechanism is adding a packet to the deferred queue,
while the out-of-sequence handling is retrieving it again, thus
ending up in a loop inside the node_lock scope.
- Even if this is avoided, the link will very often send out
unnecessary protocol messages, in the worst case leading to
redundant retransmissions.
We fix this by just dropping arriving packets on the upcoming link
during the synchronization phase, thus relying on the retransmission
protocol to resolve the situation once the two links have arrived to
a synchronized state.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: 35b9dd7607f0 ("tipc: add bearer get/dump to new netlink api")
Fixes: 7be57fc69184 ("tipc: add link get/dump to new netlink api")
Fixes: 46f15c6794fb ("tipc: add media get/dump to new netlink api")
CC: Richard Alpe <richard.alpe@ericsson.com>
CC: Jon Maloy <jon.maloy@ericsson.com>
CC: Ying Xue <ying.xue@windriver.com>
CC: tipc-discussion@lists.sourceforge.net
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: e5a55a898720 ("net: create generic bridge ops")
Fixes: 815cccbf10b2 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: 37a393bc4932 ("bridge: notify mdb changes via netlink")
CC: Cong Wang <amwang@redhat.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This action is meant to be passive, i.e. we should not alter
skb->nfct: If nfct is present just leave it alone.
Compile tested only.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 3cdaa5be9e81a914e633a6be7b7d2ef75b528562 ("ipv4: Don't
increase PMTU with Datagram Too Big message") broke PMTU in cases
where the rt_pmtu value has expired but is smaller than the new
PMTU value.
This obsolete rt_pmtu then prevents the new PMTU value from being
installed.
Fixes: 3cdaa5be9e81 ("ipv4: Don't increase PMTU with Datagram Too Big message")
Reported-by: Gerd v. Egidy <gerd.von.egidy@intra2net.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Fix a crash in nf_tables when dictionaries are used from the ruleset,
due to memory corruption, from Florian Westphal.
2) Fix another crash in nf_queue when used with br_netfilter. Also from
Florian.
Both fixes are related to new stuff that got in 4.0-rc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) mlx4 doesn't check fully for supported valid RSS hash function, fix
from Amir Vadai
2) Off by one in ibmveth_change_mtu(), from David Gibson
3) Prevent altera chip from reporting false error interrupts in some
circumstances, from Chee Nouk Phoon
4) Get rid of that stupid endless loop trying to allocate a FIN packet
in TCP, and in the process kill deadlocks. From Eric Dumazet
5) Fix get_rps_cpus() crash due to wrong invalid-cpu value, also from
Eric Dumazet
6) Fix two bugs in async rhashtable resizing, from Thomas Graf
7) Fix topology server listener socket namespace bug in TIPC, from Ying
Xue
8) Add some missing HAS_DMA kconfig dependencies, from Geert
Uytterhoeven
9) bgmac driver intends to force re-polling but does so by returning
the wrong value from it's ->poll() handler. Fix from Rafał Miłecki
10) When the creater of an rhashtable configures a max size for it,
don't bark in the logs and drop insertions when that is exceeded.
Fix from Johannes Berg
11) Recover from out of order packets in ppp mppe properly, from Sylvain
Rochet
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
bnx2x: really disable TPA if 'disable_tpa' option is set
net:treewide: Fix typo in drivers/net
net/mlx4_en: Prevent setting invalid RSS hash function
mdio-mux-gpio: use new gpiod_get_array and gpiod_put_array functions
netfilter; Add some missing default cases to switch statements in nft_reject.
ppp: mppe: discard late packet in stateless mode
ppp: mppe: sanity error path rework
net/bonding: Make DRV macros private
net: rfs: fix crash in get_rps_cpus()
altera tse: add support for fixed-links.
pxa168: fix double deallocation of managed resources
net: fix crash in build_skb()
net: eth: altera: Resolve false errors from MSGDMA to TSE
ehea: Fix memory hook reference counting crashes
net/tg3: Release IRQs on permanent error
net: mdio-gpio: support access that may sleep
inet: fix possible panic in reqsk_queue_unlink()
rhashtable: don't attempt to grow when at max_size
bgmac: fix requests for extra polling calls from NAPI
tcp: avoid looping in tcp_send_fin()
...
|
|
This fixes:
====================
net/netfilter/nft_reject.c: In function ‘nft_reject_dump’:
net/netfilter/nft_reject.c:61:2: warning: enumeration value ‘NFT_REJECT_TCP_RST’ not handled in switch [-Wswitch]
switch (priv->type) {
^
net/netfilter/nft_reject.c:61:2: warning: enumeration value ‘NFT_REJECT_ICMPX_UNREACH’ not handled in switch [-Wswi\
tch]
net/netfilter/nft_reject_inet.c: In function ‘nft_reject_inet_dump’:
net/netfilter/nft_reject_inet.c:105:2: warning: enumeration value ‘NFT_REJECT_TCP_RST’ not handled in switch [-Wswi\
tch]
switch (priv->type) {
^
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull NFS client updates from Trond Myklebust:
"Another set of mainly bugfixes and a couple of cleanups. No new
functionality in this round.
Highlights include:
Stable patches:
- Fix a regression in /proc/self/mountstats
- Fix the pNFS flexfiles O_DIRECT support
- Fix high load average due to callback thread sleeping
Bugfixes:
- Various patches to fix the pNFS layoutcommit support
- Do not cache pNFS deviceids unless server notifications are enabled
- Fix a SUNRPC transport reconnection regression
- make debugfs file creation failure non-fatal in SUNRPC
- Another fix for circular directory warnings on NFSv4 "junctioned"
mountpoints
- Fix locking around NFSv4.2 fallocate() support
- Truncating NFSv4 file opens should also sync O_DIRECT writes
- Prevent infinite loop in rpcrdma_ep_create()
Features:
- Various improvements to the RDMA transport code's handling of
memory registration
- Various code cleanups"
* tag 'nfs-for-4.1-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (55 commits)
fs/nfs: fix new compiler warning about boolean in switch
nfs: Remove unneeded casts in nfs
NFS: Don't attempt to decode missing directory entries
Revert "nfs: replace nfs_add_stats with nfs_inc_stats when add one"
NFS: Rename idmap.c to nfs4idmap.c
NFS: Move nfs_idmap.h into fs/nfs/
NFS: Remove CONFIG_NFS_V4 checks from nfs_idmap.h
NFS: Add a stub for GETDEVICELIST
nfs: remove WARN_ON_ONCE from nfs_direct_good_bytes
nfs: fix DIO good bytes calculation
nfs: Fetch MOUNTED_ON_FILEID when updating an inode
sunrpc: make debugfs file creation failure non-fatal
nfs: fix high load average due to callback thread sleeping
NFS: Reduce time spent holding the i_mutex during fallocate()
NFS: Don't zap caches on fallocate()
xprtrdma: Make rpcrdma_{un}map_one() into inline functions
xprtrdma: Handle non-SEND completions via a callout
xprtrdma: Add "open" memreg op
xprtrdma: Add "destroy MRs" memreg op
xprtrdma: Add "reset MRs" memreg op
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
|
|
Commit 567e4b79731c ("net: rfs: add hash collision detection") had one
mistake :
RPS_NO_CPU is no longer the marker for invalid cpu in set_rps_cpu()
and get_rps_cpu(), as @next_cpu was the result of an AND with
rps_cpu_mask
This bug showed up on a host with 72 cpus :
next_cpu was 0x7f, and the code was trying to access percpu data of an
non existent cpu.
In a follow up patch, we might get rid of compares against nr_cpu_ids,
if we init the tables with 0. This is silly to test for a very unlikely
condition that exists only shortly after table initialization, as
we got rid of rps_reset_sock_flow() and similar functions that were
writing this RPS_NO_CPU magic value at flow dismantle : When table is
old enough, it never contains this value anymore.
Fixes: 567e4b79731c ("net: rfs: add hash collision detection")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When I added pfmemalloc support in build_skb(), I forgot netlink
was using build_skb() with a vmalloc() area.
In this patch I introduce __build_skb() for netlink use,
and build_skb() is a wrapper handling both skb->head_frag and
skb->pfmemalloc
This means netlink no longer has to hack skb->head_frag
[ 1567.700067] kernel BUG at arch/x86/mm/physaddr.c:26!
[ 1567.700067] invalid opcode: 0000 [#1] PREEMPT SMP KASAN
[ 1567.700067] Dumping ftrace buffer:
[ 1567.700067] (ftrace buffer empty)
[ 1567.700067] Modules linked in:
[ 1567.700067] CPU: 9 PID: 16186 Comm: trinity-c182 Not tainted 4.0.0-next-20150424-sasha-00037-g4796e21 #2167
[ 1567.700067] task: ffff880127efb000 ti: ffff880246770000 task.ti: ffff880246770000
[ 1567.700067] RIP: __phys_addr (arch/x86/mm/physaddr.c:26 (discriminator 3))
[ 1567.700067] RSP: 0018:ffff8802467779d8 EFLAGS: 00010202
[ 1567.700067] RAX: 000041000ed8e000 RBX: ffffc9008ed8e000 RCX: 000000000000002c
[ 1567.700067] RDX: 0000000000000004 RSI: 0000000000000000 RDI: ffffffffb3fd6049
[ 1567.700067] RBP: ffff8802467779f8 R08: 0000000000000019 R09: ffff8801d0168000
[ 1567.700067] R10: ffff8801d01680c7 R11: ffffed003a02d019 R12: ffffc9000ed8e000
[ 1567.700067] R13: 0000000000000f40 R14: 0000000000001180 R15: ffffc9000ed8e000
[ 1567.700067] FS: 00007f2a7da3f700(0000) GS:ffff8801d1000000(0000) knlGS:0000000000000000
[ 1567.700067] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1567.700067] CR2: 0000000000738308 CR3: 000000022e329000 CR4: 00000000000007e0
[ 1567.700067] Stack:
[ 1567.700067] ffffc9000ed8e000 ffff8801d0168000 ffffc9000ed8e000 ffff8801d0168000
[ 1567.700067] ffff880246777a28 ffffffffad7c0a21 0000000000001080 ffff880246777c08
[ 1567.700067] ffff88060d302e68 ffff880246777b58 ffff880246777b88 ffffffffad9a6821
[ 1567.700067] Call Trace:
[ 1567.700067] build_skb (include/linux/mm.h:508 net/core/skbuff.c:316)
[ 1567.700067] netlink_sendmsg (net/netlink/af_netlink.c:1633 net/netlink/af_netlink.c:2329)
[ 1567.774369] ? sched_clock_cpu (kernel/sched/clock.c:311)
[ 1567.774369] ? netlink_unicast (net/netlink/af_netlink.c:2273)
[ 1567.774369] ? netlink_unicast (net/netlink/af_netlink.c:2273)
[ 1567.774369] sock_sendmsg (net/socket.c:614 net/socket.c:623)
[ 1567.774369] sock_write_iter (net/socket.c:823)
[ 1567.774369] ? sock_sendmsg (net/socket.c:806)
[ 1567.774369] __vfs_write (fs/read_write.c:479 fs/read_write.c:491)
[ 1567.774369] ? get_lock_stats (kernel/locking/lockdep.c:249)
[ 1567.774369] ? default_llseek (fs/read_write.c:487)
[ 1567.774369] ? vtime_account_user (kernel/sched/cputime.c:701)
[ 1567.774369] ? rw_verify_area (fs/read_write.c:406 (discriminator 4))
[ 1567.774369] vfs_write (fs/read_write.c:539)
[ 1567.774369] SyS_write (fs/read_write.c:586 fs/read_write.c:577)
[ 1567.774369] ? SyS_read (fs/read_write.c:577)
[ 1567.774369] ? __this_cpu_preempt_check (lib/smp_processor_id.c:63)
[ 1567.774369] ? trace_hardirqs_on_caller (kernel/locking/lockdep.c:2594 kernel/locking/lockdep.c:2636)
[ 1567.774369] ? trace_hardirqs_on_thunk (arch/x86/lib/thunk_64.S:42)
[ 1567.774369] system_call_fastpath (arch/x86/kernel/entry_64.S:261)
Fixes: 79930f5892e ("net: do not deplete pfmemalloc reserve")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NFT_JUMP/GOTO erronously sets length to sizeof(void *).
We then allocate insufficient memory when such element is added to a vmap.
Suggested-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
[ 3897.923145] BUG: unable to handle kernel NULL pointer dereference at
0000000000000080
[ 3897.931025] IP: [<ffffffffa9f27686>] reqsk_timer_handler+0x1a6/0x243
There is a race when reqsk_timer_handler() and tcp_check_req() call
inet_csk_reqsk_queue_unlink() on the same req at the same time.
Before commit fa76ce7328b2 ("inet: get rid of central tcp/dccp listener
timer"), listener spinlock was held and race could not happen.
To solve this bug, we change reqsk_queue_unlink() to not assume req
must be found, and we return a status, to conditionally release a
refcount on the request sock.
This also means tcp_check_req() in non fastopen case might or not
consume req refcount, so tcp_v6_hnd_req() & tcp_v4_hnd_req() have
to properly handle this.
(Same remark for dccp_check_req() and its callers)
inet_csk_reqsk_queue_drop() is now too big to be inlined, as it is
called 4 times in tcp and 3 times in dccp.
Fixes: fa76ce7328b2 ("inet: get rid of central tcp/dccp listener timer")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Presence of an unbound loop in tcp_send_fin() had always been hard
to explain when analyzing crash dumps involving gigantic dying processes
with millions of sockets.
Lets try a different strategy :
In case of memory pressure, try to add the FIN flag to last packet
in write queue, even if packet was already sent. TCP stack will
be able to deliver this FIN after a timeout event. Note that this
FIN being delivered by a retransmit, it also carries a Push flag
given our current implementation.
By checking sk_under_memory_pressure(), we anticipate that cooking
many FIN packets might deplete tcp memory.
In the case we could not allocate a packet, even with __GFP_WAIT
allocation, then not sending a FIN seems quite reasonable if it allows
to get rid of this socket, free memory, and not block the process from
eventually doing other useful work.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hashtable behaviour change was merged into the tree
at about the same time as the mac80211 use of rhashtable,
but of course these don't really conflict in the normal
sense. Enable hash table shrinking now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
NFS: NFSoRDMA Client Changes
This patch series creates an operation vector for each of the different
memory registration modes. This should make it easier to one day increase
credit limit, rsize, and wsize.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
* bugfixes:
NFSv4: Return delegations synchronously in evict_inode
SUNRPC: Fix a regression when reconnecting
NFS: remount with security change should return EINVAL
nfs: do not export discarded symbols
NFSv4.1: don't export static symbol
|
|
v2: gracefully handle the case where some dentry pointers end up NULL
and be more dilligent about zeroing out dentry pointers
We currently have a problem that SELinux policy is being enforced when
creating debugfs files. If a debugfs file is created as a side effect of
doing some syscall, then that creation can fail if the SELinux policy
for that process prevents it.
This seems wrong. We don't do that for files under /proc, for instance,
so Bruce has proposed a patch to fix that.
While discussing that patch however, Greg K.H. stated:
"No kernel code should care / fail if a debugfs function fails, so
please fix up the sunrpc code first."
This patch converts all of the sunrpc debugfs setup code to be void
return functins, and the callers to not look for errors from those
functions.
This should allow rpc_clnt and rpc_xprt creation to work, even if the
kernel fails to create debugfs files for some reason.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
fixed several comment and whitespace style issues
Signed-off-by: Jason Eastman <eastman.jason.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When link statistics is dumped over netlink, we iterate over
the list of peer nodes and append each links statistics to
the netlink msg. In the case where the dump is resumed after
filling up a nlmsg, the node refcnt is decremented without
having been incremented previously which may cause the node
reference to be freed. When this happens, the following
info/stacktrace will be generated, followed by a crash or
undefined behavior.
We fix this by removing the erroneous call to tipc_node_put
inside the loop that iterates over nodes.
[ 384.312303] INFO: trying to register non-static key.
[ 384.313110] the code is fine but needs lockdep annotation.
[ 384.313290] turning off the locking correctness validator.
[ 384.313290] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.0.0+ #13
[ 384.313290] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 384.313290] ffff88003c6d0290 ffff88003cc03ca8 ffffffff8170adf1 0000000000000007
[ 384.313290] ffffffff82728730 ffff88003cc03d38 ffffffff810a6a6d 00000000001d7200
[ 384.313290] ffff88003c6d0ab0 ffff88003cc03ce8 0000000000000285 0000000000000001
[ 384.313290] Call Trace:
[ 384.313290] <IRQ> [<ffffffff8170adf1>] dump_stack+0x4c/0x65
[ 384.313290] [<ffffffff810a6a6d>] __lock_acquire+0xf3d/0xf50
[ 384.313290] [<ffffffff810a7375>] lock_acquire+0xd5/0x290
[ 384.313290] [<ffffffffa0043e8c>] ? link_timeout+0x1c/0x170 [tipc]
[ 384.313290] [<ffffffffa0043e70>] ? link_state_event+0x4e0/0x4e0 [tipc]
[ 384.313290] [<ffffffff81712890>] _raw_spin_lock_bh+0x40/0x80
[ 384.313290] [<ffffffffa0043e8c>] ? link_timeout+0x1c/0x170 [tipc]
[ 384.313290] [<ffffffffa0043e8c>] link_timeout+0x1c/0x170 [tipc]
[ 384.313290] [<ffffffff810c4698>] call_timer_fn+0xb8/0x490
[ 384.313290] [<ffffffff810c45e0>] ? process_timeout+0x10/0x10
[ 384.313290] [<ffffffff810c5a2c>] run_timer_softirq+0x21c/0x420
[ 384.313290] [<ffffffffa0043e70>] ? link_state_event+0x4e0/0x4e0 [tipc]
[ 384.313290] [<ffffffff8105a954>] __do_softirq+0xf4/0x630
[ 384.313290] [<ffffffff8105afdd>] irq_exit+0x5d/0x60
[ 384.313290] [<ffffffff8103ade1>] smp_apic_timer_interrupt+0x41/0x50
[ 384.313290] [<ffffffff817144a0>] apic_timer_interrupt+0x70/0x80
[ 384.313290] <EOI> [<ffffffff8100db10>] ? default_idle+0x20/0x210
[ 384.313290] [<ffffffff8100db0e>] ? default_idle+0x1e/0x210
[ 384.313290] [<ffffffff8100e61a>] arch_cpu_idle+0xa/0x10
[ 384.313290] [<ffffffff81099803>] cpu_startup_entry+0x2c3/0x530
[ 384.313290] [<ffffffff810d2893>] ? clockevents_register_device+0x113/0x200
[ 384.313290] [<ffffffff81038b0f>] start_secondary+0x13f/0x170
Fixes: 8a0f6ebe8494 ("tipc: involve reference counter for node structure")
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the function tipc_sk_rcv(), the stack variable 'err'
is only initialized to TIPC_ERR_NO_PORT for the first
iteration over the link input queue. If a chain of messages
are received from a link, failure to lookup the socket for
any but the first message will cause the message to bounce back
out on a random link.
We fix this by properly initializing err.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a new topology server is launched in a new namespace, its
listening socket is inserted into the "init ns" namespace's socket
hash table rather than the one owned by the new namespace. Although
the socket's namespace is forcedly changed to the new namespace later,
the socket is still stored in the socket hash table of "init ns"
namespace. When a client created in the new namespace connects
its own topology server, the connection is failed as its server's
socket could not be found from its own namespace's socket table.
If __sock_create() instead of original sock_create_kern() is used
to create the server's socket through specifying an expected namesapce,
the socket will be inserted into the specified namespace's socket
table, thereby avoiding to the topology server broken issue.
Fixes: 76100a8a64bc ("tipc: fix netns refcnt leak")
Reported-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
My conversion of the mac80211 station hash table to rhashtable
completely broke the lookup in sta_info_get() as it no longer
took into account the virtual interface. Fix that.
Fixes: 7bedd0cfad4e1 ("mac80211: use rhashtable for station table")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
build_skb() should look at the page pfmemalloc status.
If set, this means page allocator allocated this page in the
expectation it would help to free other pages. Networking
stack can do that only if skb->pfmemalloc is also set.
Also, we must refrain using high order pages from the pfmemalloc
reserve, so __page_frag_refill() must also use __GFP_NOMEMALLOC for
them. Under memory pressure, using order-0 pages is probably the best
strategy.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code there just open-codes the same, so use the provided macro instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph updates from Sage Weil:
"This time around we have a collection of CephFS fixes from Zheng
around MDS failure handling and snapshots, support for a new CRUSH
straw2 algorithm (to sync up with userspace) and several RBD cleanups
and fixes from Ilya, an error path leak fix from Taesoo, and then an
assorted collection of cleanups from others"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (28 commits)
rbd: rbd_wq comment is obsolete
libceph: announce support for straw2 buckets
crush: straw2 bucket type with an efficient 64-bit crush_ln()
crush: ensuring at most num-rep osds are selected
crush: drop unnecessary include from mapper.c
ceph: fix uninline data function
ceph: rename snapshot support
ceph: fix null pointer dereference in send_mds_reconnect()
ceph: hold on to exclusive caps on complete directories
libceph: simplify our debugfs attr macro
ceph: show non-default options only
libceph: expose client options through debugfs
libceph, ceph: split ceph_show_options()
rbd: mark block queue as non-rotational
libceph: don't overwrite specific con error msgs
ceph: cleanup unsafe requests when reconnecting is denied
ceph: don't zero i_wrbuffer_ref when reconnecting is denied
ceph: don't mark dirty caps when there is no auth cap
ceph: keep i_snap_realm while there are writers
libceph: osdmap.h: Add missing format newlines
...
|
|
The reserved implicit-NULL label isn't allowed to appear in the label
stack for packets, so make it an error for the control plane to
specify it as an outgoing label.
Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An MPLS network is a single trust domain where the edges must be in
control of what labels make their way into the core. The simplest way
of ensuring this is for the edge device to always impose the labels,
and not allow forward labeled traffic from untrusted neighbours. This
is achieved by allowing a per-device configuration of whether MPLS
traffic input from that interface should be processed or not.
To be secure by default, the default state is changed to MPLS being
disabled on all interfaces unless explicitly enabled and no global
option is provided to change the default. Whilst this differs from
other protocols (e.g. IPv6), network operators are used to explicitly
enabling MPLS forwarding on interfaces, and with the number of links
to the MPLS core typically fairly low this doesn't present too much of
a burden on operators.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add per-device MPLS state to supported interfaces. Use the presence of
this state in mpls_route_add to determine that this is a supported
interface.
Use the presence of mpls_dev to drop packets that arrived on an
unsupported interface - previously they were allowed through.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using sk_stream_alloc_skb() in tcp_send_fin() is dangerous in
case a huge process is killed by OOM, and tcp_mem[2] is hit.
To be able to free memory we need to make progress, so this
patch allows FIN packets to not care about tcp_mem[2], if
skb allocation succeeded.
In a follow-up patch, we might abort tcp_send_fin() infinite loop
in case TIF_MEMDIE is set on this thread, as memory allocator
did its best getting extra memory already.
This patch reverts d22e15371811 ("tcp: fix tcp fin memory accounting")
Fixes: d22e15371811 ("tcp: fix tcp fin memory accounting")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is an improved straw bucket that correctly avoids any data movement
between items A and B when neither A nor B's weights are changed. Said
differently, if we adjust the weight of item C (including adding it anew
or removing it completely), we will only see inputs move to or from C,
never between other items in the bucket.
Notably, there is not intermediate scaling factor that needs to be
calculated. The mapping function is a simple function of the item weights.
The below commits were squashed together into this one (mostly to avoid
adding and then yanking a ~6000 lines worth of crush_ln_table):
- crush: add a straw2 bucket type
- crush: add crush_ln to calculate nature log efficently
- crush: improve straw2 adjustment slightly
- crush: change crush_ln to provide 32 more digits
- crush: fix crush_get_bucket_item_weight and bucket destroy for straw2
- crush/mapper: fix divide-by-0 in straw2
(with div64_s64() for draw = ln / w and INT64_MIN -> S64_MIN - need
to create a proper compat.h in ceph.git)
Reflects ceph.git commits 242293c908e923d474910f2b8203fa3b41eb5a53,
32a1ead92efcd351822d22a5fc37d159c65c1338,
6289912418c4a3597a11778bcf29ed5415117ad9,
35fcb04e2945717cf5cfe150b9fa89cb3d2303a1,
6445d9ee7290938de1e4ee9563912a6ab6d8ee5f,
b5921d55d16796e12d66ad2c4add7305f9ce2353.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Crush temporary buffers are allocated as per replica size configured
by the user. When there are more final osds (to be selected as per
rule) than the replicas, buffer overlaps and it causes crash. Now, it
ensures that at most num-rep osds are selected even if more number of
osds are allowed by the rule.
Reflects ceph.git commits 6b4d1aa99718e3b367496326c1e64551330fabc0,
234b066ba04976783d15ff2abc3e81b6cc06fb10.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Pull networking fixes from David Miller:
"Just a few fixes trickling in at this point.
1) If we see an attached socket on an skb in the ipv4 forwarding path,
bail. This can happen due to races with FIB rule addition, and
deletion, and we should just drop such frames. From Sebastian
Pöhn.
2) pppoe receive should only accept packets destined for this hosts's
MAC address. From Joakim Tjernlund.
3) Handle checksum unwrapping properly in ppp receive properly when
it's encapsulated in UDP in some way, fix from Tom Herbert.
4) Fix some bugs in mv88e6xxx DSA driver resulting from the conversion
from register offset constants to mnenomic macros. From Vivien
Didelot.
5) Fix handling of HCA max message size in mlx4 adapters, from Eran
Ben ELisha"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net/mlx4_core: Fix reading HCA max message size in mlx4_QUERY_DEV_CAP
tcp: add memory barriers to write space paths
altera tse: Error-Bit on tx-avalon-stream always set.
net: dsa: mv88e6xxx: use PORT_DEFAULT_VLAN
net: dsa: mv88e6xxx: fix setup of port control 1
ppp: call skb_checksum_complete_unset in ppp_receive_frame
net: add skb_checksum_complete_unset
pppoe: Lacks DST MAC address check
ip_forward: Drop frames with attached skb->sk
|
|
Ensure that we either see that the buffer has write space
in tcp_poll() or that we perform a wakeup from the input
side. Did not run into any actual problem here, but thought
that we should make things explicit.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initial discussion was:
[FYI] xfrm: Don't lookup sk_policy for timewait sockets
Forwarded frames should not have a socket attached. Especially
tw sockets will lead to panics later-on in the stack.
This was observed with TPROXY assigning a tw socket and broken
policy routing (misconfigured). As a result frame enters
forwarding path instead of input. We cannot solve this in
TPROXY as it cannot know that policy routing is broken.
v2:
Remove useless comment
Signed-off-by: Sebastian Poehn <sebastian.poehn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a client_options attribute for showing libceph options.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Split ceph_show_options() into two pieces and move the piece
responsible for printing client (libceph) options into net/ceph. This
way people adding a libceph option wouldn't have to remember to update
code in fs/ceph.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
- specific con->error_msg messages (e.g. "protocol version mismatch")
end up getting overwritten by a catch-all "socket error on read
/ write", introduced in commit 3a140a0d5c4b ("libceph: report socket
read/write error message")
- "bad message sequence # for incoming message" loses to "bad crc" due
to the fact that -EBADMSG is used for both
Fix it, and tidy up con->error_msg assignments and pr_errs while at it.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Stations assigned to an AP_VLAN type interface are flushed
when the interface is stopped, but then we warn about it.
Suppress the warning since there's nothing else that would
ensure those stations are already removed at this point.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
Pull 9pfs updates from Eric Van Hensbergen:
"Some accumulated cleanup patches for kerneldoc and unused variables as
well as some lock bug fixes and adding privateport option for RDMA"
* tag 'for-linus-4.1-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
net/9p: add a privport option for RDMA transport.
fs/9p: Initialize status in v9fs_file_do_lock.
net/9p: Initialize opts->privport as it should be.
net/9p: use memcpy() instead of snprintf() in p9_mount_tag_show()
9p: use unsigned integers for nwqid/count
9p: do not crash on unknown lock status code
9p: fix error handling in v9fs_file_do_lock
9p: remove unused variable in p9_fd_create()
9p: kerneldoc warning fixes
|
|
While it is not used by newer userspace anymore, the older userspace was
utilizing HIDP_VIRTUAL_CABLE_UNPLUG and HIDP_BOOT_PROTOCOL_MODE flags
when adding a new HIDP connection.
The flags validation is important, but we can not break older userspace
and with that allow providing these flags even if newer userspace does
not use them anymore.
Reported-and-tested-by: Jörg Otte <jrg.otte@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull networking fixes from David Miller:
1) Fix verifier memory corruption and other bugs in BPF layer, from
Alexei Starovoitov.
2) Add a conservative fix for doing BPF properly in the BPF classifier
of the packet scheduler on ingress. Also from Alexei.
3) The SKB scrubber should not clear out the packet MARK and security
label, from Herbert Xu.
4) Fix oops on rmmod in stmmac driver, from Bryan O'Donoghue.
5) Pause handling is not correct in the stmmac driver because it
doesn't take into consideration the RX and TX fifo sizes. From
Vince Bridgers.
6) Failure path missing unlock in FOU driver, from Wang Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
net: dsa: use DEVICE_ATTR_RW to declare temp1_max
netns: remove BUG_ONs from net_generic()
IB/ipoib: Fix ndo_get_iflink
sfc: Fix memcpy() with const destination compiler warning.
altera tse: Fix network-delays and -retransmissions after high throughput.
net: remove unused 'dev' argument from netif_needs_gso()
act_mirred: Fix bogus header when redirecting from VLAN
inet_diag: fix access to tcp cc information
tcp: tcp_get_info() should fetch socket fields once
net: dsa: mv88e6xxx: Add missing initialization in mv88e6xxx_set_port_state()
skbuff: Do not scrub skb mark within the same name space
Revert "net: Reset secmark when scrubbing packet"
bpf: fix two bugs in verification logic when accessing 'ctx' pointer
bpf: fix bpf helpers to use skb->mac_header relative offsets
stmmac: Configure Flow Control to work correctly based on rxfifo size
stmmac: Enable unicast pause frame detect in GMAC Register 6
stmmac: Read tx-fifo-depth and rx-fifo-depth from the devicetree
stmmac: Add defines and documentation for enabling flow control
stmmac: Add properties for transmit and receive fifo sizes
stmmac: fix oops on rmmod after assigning ip addr
...
|
|
Since commit da4759c (sysfs: Use only return value from is_visible for
the file mode), it is possible to reduce the permissions of a file.
So declare temp1_max with the DEVICE_ATTR_RW macro and remove the write
permission in dsa_hwmon_attrs_visible if set_temp_limit isn't provided.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 04ffcb255f22 ("net: Add ndo_gso_check") Tom originally
added the 'dev' argument to be able to call ndo_gso_check().
Then later, when generalizing this in commit 5f35227ea34b
("net: Generalize ndo_gso_check to ndo_features_check")
Jesse removed the call to ndo_gso_check() in netif_needs_gso()
by calling the new ndo_features_check() in a different place.
This made the 'dev' argument unused.
Remove the unused argument and go back to the code as before.
Cc: Tom Herbert <therbert@google.com>
Cc: Jesse Gross <jesse@nicira.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When you redirect a VLAN device to any device, you end up with
crap in af_packet on the xmit path because hard_header_len is
not equal to skb->mac_len. So the redirected packet contains
four extra bytes at the start which then gets interpreted as
part of the MAC address.
This patch fixes this by only pushing skb->mac_len. We also
need to fix ifb because it tries to undo the pushing done by
act_mirred.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two different problems are fixed here :
1) inet_sk_diag_fill() might be called without socket lock held.
icsk->icsk_ca_ops can change under us and module be unloaded.
-> Access to freed memory.
Fix this using rcu_read_lock() to prevent module unload.
2) Some TCP Congestion Control modules provide information
but again this is not safe against icsk->icsk_ca_ops
change and nla_put() errors were ignored. Some sockets
could not get the additional info if skb was almost full.
Fix this by returning a status from get_info() handlers and
using rcu protection as well.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_get_info() can be called without holding socket lock,
so any socket fields can change under us.
Use READ_ONCE() to fetch sk_pacing_rate and sk_max_pacing_rate
Fixes: 977cb0ecf82e ("tcp: add pacing_rate information into tcp_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Wed, Apr 15, 2015 at 05:41:26PM +0200, Nicolas Dichtel wrote:
> Le 15/04/2015 15:57, Herbert Xu a écrit :
> >On Wed, Apr 15, 2015 at 06:22:29PM +0800, Herbert Xu wrote:
> [snip]
> >Subject: skbuff: Do not scrub skb mark within the same name space
> >
> >The commit ea23192e8e577dfc51e0f4fc5ca113af334edff9 ("tunnels:
> Maybe add a Fixes tag?
> Fixes: ea23192e8e57 ("tunnels: harmonize cleanup done on skb on rx path")
>
> >harmonize cleanup done on skb on rx path") broke anyone trying to
> >use netfilter marking across IPv4 tunnels. While most of the
> >fields that are cleared by skb_scrub_packet don't matter, the
> >netfilter mark must be preserved.
> >
> >This patch rearranges skb_scurb_packet to preserve the mark field.
> nit: s/scurb/scrub
>
> Else it's fine for me.
Sure.
PS I used the wrong email for James the first time around. So
let me repeat the question here. Should secmark be preserved
or cleared across tunnels within the same name space? In fact,
do our security models even support name spaces?
---8<---
The commit ea23192e8e577dfc51e0f4fc5ca113af334edff9 ("tunnels:
harmonize cleanup done on skb on rx path") broke anyone trying to
use netfilter marking across IPv4 tunnels. While most of the
fields that are cleared by skb_scrub_packet don't matter, the
netfilter mark must be preserved.
This patch rearranges skb_scrub_packet to preserve the mark field.
Fixes: ea23192e8e57 ("tunnels: harmonize cleanup done on skb on rx path")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reverts commit b8fb4e0648a2ab3734140342002f68fb0c7d1602
because the secmark must be preserved even when a packet crosses
namespace boundaries. The reason is that security labels apply to
the system as a whole and is not per-namespace.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the short-term solution, lets fix bpf helper functions to use
skb->mac_header relative offsets instead of skb->data in order to
get the same eBPF programs with cls_bpf and act_bpf work on ingress
and egress qdisc path. We need to ensure that mac_header is set
before calling into programs. This is effectively the first option
from below referenced discussion.
More long term solution for LD_ABS|LD_IND instructions will be more
intrusive but also more beneficial than this, and implemented later
as it's too risky at this point in time.
I.e., we plan to look into the option of moving skb_pull() out of
eth_type_trans() and into netif_receive_skb() as has been suggested
as second option. Meanwhile, this solution ensures ingress can be
used with eBPF, too, and that we won't run into ABI troubles later.
For dealing with negative offsets inside eBPF helper functions,
we've implemented bpf_skb_clone_unwritable() to test for unwriteable
headers.
Reference: http://thread.gmane.org/gmane.linux.network/359129/focus=359694
Fixes: 608cd71a9c7c ("tc: bpf: generalize pedit action")
Fixes: 91bc4822c3d6 ("tc: bpf: add checksum helpers")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove duplicated include.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: 7a6c8c34e5b7 ("fou: implement FOU_CMD_GET")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge second patchbomb from Andrew Morton:
- the rest of MM
- various misc bits
- add ability to run /sbin/reboot at reboot time
- printk/vsprintf changes
- fiddle with seq_printf() return value
* akpm: (114 commits)
parisc: remove use of seq_printf return value
lru_cache: remove use of seq_printf return value
tracing: remove use of seq_printf return value
cgroup: remove use of seq_printf return value
proc: remove use of seq_printf return value
s390: remove use of seq_printf return value
cris fasttimer: remove use of seq_printf return value
cris: remove use of seq_printf return value
openrisc: remove use of seq_printf return value
ARM: plat-pxa: remove use of seq_printf return value
nios2: cpuinfo: remove use of seq_printf return value
microblaze: mb: remove use of seq_printf return value
ipc: remove use of seq_printf return value
rtc: remove use of seq_printf return value
power: wakeup: remove use of seq_printf return value
x86: mtrr: if: remove use of seq_printf return value
linux/bitmap.h: improve BITMAP_{LAST,FIRST}_WORD_MASK
MAINTAINERS: CREDITS: remove Stefano Brivio from B43
.mailmap: add Ricardo Ribalda
CREDITS: add Ricardo Ribalda Delgado
...
|
|
The current semantics of string_escape_mem are inadequate for one of its
current users, vsnprintf(). If that is to honour its contract, it must
know how much space would be needed for the entire escaped buffer, and
string_escape_mem provides no way of obtaining that (short of allocating a
large enough buffer (~4 times input string) to let it play with, and
that's definitely a big no-no inside vsnprintf).
So change the semantics for string_escape_mem to be more snprintf-like:
Return the size of the output that would be generated if the destination
buffer was big enough, but of course still only write to the part of dst
it is allowed to, and (contrary to snprintf) don't do '\0'-termination.
It is then up to the caller to detect whether output was truncated and to
append a '\0' if desired. Also, we must output partial escape sequences,
otherwise a call such as snprintf(buf, 3, "%1pE", "\123") would cause
printf to write a \0 to buf[2] but leaving buf[0] and buf[1] with whatever
they previously contained.
This also fixes a bug in the escaped_string() helper function, which used
to unconditionally pass a length of "end-buf" to string_escape_mem();
since the latter doesn't check osz for being insanely large, it would
happily write to dst. For example, kasprintf(GFP_KERNEL, "something and
then %pE", ...); is an easy way to trigger an oops.
In test-string_helpers.c, the -ENOMEM test is replaced with testing for
getting the expected return value even if the buffer is too small. We
also ensure that nothing is written (by relying on a NULL pointer deref)
if the output size is 0 by passing NULL - this has to work for
kasprintf("%pE") to work.
In net/sunrpc/cache.c, I think qword_add still has the same semantics.
Someone should definitely double-check this.
In fs/proc/array.c, I made the minimum possible change, but longer-term it
should stop poking around in seq_file internals.
[andriy.shevchenko@linux.intel.com: simplify qword_add]
[andriy.shevchenko@linux.intel.com: add missed curly braces]
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are a lot of embedded systems that run most or all of their
functionality in init, running as root:root. For these systems,
supporting multiple users is not necessary.
This patch adds a new symbol, CONFIG_MULTIUSER, that makes support for
non-root users, non-root groups, and capabilities optional. It is enabled
under CONFIG_EXPERT menu.
When this symbol is not defined, UID and GID are zero in any possible case
and processes always have all capabilities.
The following syscalls are compiled out: setuid, setregid, setgid,
setreuid, setresuid, getresuid, setresgid, getresgid, setgroups,
getgroups, setfsuid, setfsgid, capget, capset.
Also, groups.c is compiled out completely.
In kernel/capability.c, capable function was moved in order to avoid
adding two ifdef blocks.
This change saves about 25 KB on a defconfig build. The most minimal
kernels have total text sizes in the high hundreds of kB rather than
low MB. (The 25k goes down a bit with allnoconfig, but not that much.
The kernel was booted in Qemu. All the common functionalities work.
Adding users/groups is not possible, failing with -ENOSYS.
Bloat-o-meter output:
add/remove: 7/87 grow/shrink: 19/397 up/down: 1675/-26325 (-24650)
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Iulia Manda <iulia.manda21@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull second vfs update from Al Viro:
"Now that net-next went in... Here's the next big chunk - killing
->aio_read() and ->aio_write().
There'll be one more pile today (direct_IO changes and
generic_write_checks() cleanups/fixes), but I'd prefer to keep that
one separate"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
->aio_read and ->aio_write removed
pcm: another weird API abuse
infinibad: weird APIs switched to ->write_iter()
kill do_sync_read/do_sync_write
fuse: use iov_iter_get_pages() for non-splice path
fuse: switch to ->read_iter/->write_iter
switch drivers/char/mem.c to ->read_iter/->write_iter
make new_sync_{read,write}() static
coredump: accept any write method
switch /dev/loop to vfs_iter_write()
serial2002: switch to __vfs_read/__vfs_write
ashmem: use __vfs_read()
export __vfs_read()
autofs: switch to __vfs_write()
new helper: __vfs_write()
switch hugetlbfs to ->read_iter()
coda: switch to ->read_iter/->write_iter
ncpfs: switch to ->read_iter/->write_iter
net/9p: remove (now-)unused helpers
p9_client_attach(): set fid->uid correctly
...
|
|
socket inodes and sunrpc filesystems - inodes owned by that code
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
places where we are dealing with S_ISSOCK file creation/lookups.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
AF_UNIX sockets should call mknod on the top layer only and should not attempt
to modify the lower layer in a layered filesystem such as overlayfs.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
|
|
Merge first patchbomb from Andrew Morton:
- arch/sh updates
- ocfs2 updates
- kernel/watchdog feature
- about half of mm/
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (122 commits)
Documentation: update arch list in the 'memtest' entry
Kconfig: memtest: update number of test patterns up to 17
arm: add support for memtest
arm64: add support for memtest
memtest: use phys_addr_t for physical addresses
mm: move memtest under mm
mm, hugetlb: abort __get_user_pages if current has been oom killed
mm, mempool: do not allow atomic resizing
memcg: print cgroup information when system panics due to panic_on_oom
mm: numa: remove migrate_ratelimited
mm: fold arch_randomize_brk into ARCH_HAS_ELF_RANDOMIZE
mm: split ET_DYN ASLR from mmap ASLR
s390: redefine randomize_et_dyn for ELF_ET_DYN_BASE
mm: expose arch_mmap_rnd when available
s390: standardize mmap_rnd() usage
powerpc: standardize mmap_rnd() usage
mips: extract logic for mmap_rnd()
arm64: standardize mmap_rnd() usage
x86: standardize mmap_rnd() usage
arm: factor out mmap ASLR into mmap_rnd
...
|
|
NOTE: this is not about __GFP_THISNODE, this is only about GFP_THISNODE.
GFP_THISNODE is a secret combination of gfp bits that have different
behavior than expected. It is a combination of __GFP_THISNODE,
__GFP_NORETRY, and __GFP_NOWARN and is special-cased in the page
allocator slowpath to fail without trying reclaim even though it may be
used in combination with __GFP_WAIT.
An example of the problem this creates: commit e97ca8e5b864 ("mm: fix
GFP_THISNODE callers and clarify") fixed up many users of GFP_THISNODE
that really just wanted __GFP_THISNODE. The problem doesn't end there,
however, because even it was a no-op for alloc_misplaced_dst_page(),
which also sets __GFP_NORETRY and __GFP_NOWARN, and
migrate_misplaced_transhuge_page(), where __GFP_NORETRY and __GFP_NOWAIT
is set in GFP_TRANSHUGE. Converting GFP_THISNODE to __GFP_THISNODE is a
no-op in these cases since the page allocator special-cases
__GFP_THISNODE && __GFP_NORETRY && __GFP_NOWARN.
It's time to just remove GFP_THISNODE entirely. We leave __GFP_THISNODE
to restrict an allocation to a local node, but remove GFP_THISNODE and
its obscurity. Instead, we require that a caller clear __GFP_WAIT if it
wants to avoid reclaim.
This allows the aforementioned functions to actually reclaim as they
should. It also enables any future callers that want to do
__GFP_THISNODE but also __GFP_NORETRY && __GFP_NOWARN to reclaim. The
rule is simple: if you don't want to reclaim, then don't set __GFP_WAIT.
Aside: ovs_flow_stats_update() really wants to avoid reclaim as well, so
it is unchanged.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Pravin Shelar <pshelar@nicira.com>
Cc: Jarno Rajahalme <jrajahalme@nicira.com>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
A final pull request, I know it's very late but this time I think it's worth a
bit of rush.
The following patchset contains Netfilter/nf_tables updates for net-next, more
specifically concatenation support and dynamic stateful expression
instantiation.
This also comes with a couple of small patches. One to fix the ebtables.h
userspace header and another to get rid of an obsolete example file in tree
that describes a nf_tables expression.
This time, I decided to paste the original descriptions. This will result in a
rather large commit description, but I think these bytes to keep.
Patrick McHardy says:
====================
netfilter: nf_tables: concatenation support
The following patches add support for concatenations, which allow multi
dimensional exact matches in O(1).
The basic idea is to split the data registers, currently consisting of
4 registers of 16 bytes each, into smaller units, 16 registers of 4
bytes each, and making sure each register store always leaves the
full 32 bit in a well defined state, meaning smaller stores will
zero the remaining bits.
Based on that, we can load multiple adjacent registers with different
values, thereby building a concatenated bigger value, and use that
value for set lookups.
Sets are changed to use variable sized extensions for their key and
data values, removing the fixed limit of 16 bytes while saving memory
if less space is needed.
As a side effect, these patches will allow some nice optimizations in
the future, like using jhash2 in nft_hash, removing the masking in
nft_cmp_fast, optimized data comparison using 32 bit word size etc.
These are not done so far however.
The patches are split up as follows:
* the first five patches add length validation to register loads and
stores to make sure we stay within bounds and prepare the validation
functions for the new addressing mode
* the next patches prepare for changing to 32 bit addressing by
introducing a struct nft_regs, which holds the verdict register as
well as the data registers. The verdict members are moved to a new
struct nft_verdict to allow to pull struct nft_data out of the stack.
* the next patches contain preparatory conversions of expressions and
sets to use 32 bit addressing
* the next patch introduces so far unused register conversion helpers
for parsing and dumping register numbers over netlink
* following is the real conversion to 32 bit addressing, consisting of
replacing struct nft_data in struct nft_regs by an array of u32s and
actually translating and validating the new register numbers.
* the final two patches add support for variable sized data items and
variable sized keys / data in set elements
The patches have been verified to work correctly with nft binaries using
both old and new addressing.
====================
Patrick McHardy says:
====================
netfilter: nf_tables: dynamic stateful expression instantiation
The following patches are the grand finale of my nf_tables set work,
using all the building blocks put in place by the previous patches
to support something like iptables hashlimit, but a lot more powerful.
Sets are extended to allow attaching expressions to set elements.
The dynset expression dynamically instantiates these expressions
based on a template when creating new set elements and evaluates
them for all new or updated set members.
In combination with concatenations this effectively creates state
tables for arbitrary combinations of keys, using the existing
expression types to maintain that state. Regular set GC takes care
of purging expired states.
We currently support two different stateful expressions, counter
and limit. Using limit as a template we can express the functionality
of hashlimit, but completely unrestricted in the combination of keys.
Using counter we can perform accounting for arbitrary flows.
The following examples from patch 5/5 show some possibilities.
Userspace syntax is still WIP, especially the listing of state
tables will most likely be seperated from normal set listings
and use a more structured format:
1. Limit the rate of new SSH connections per host, similar to iptables
hashlimit:
flow ip saddr timeout 60s \
limit 10/second \
accept
2. Account network traffic between each set of /24 networks:
flow ip saddr & 255.255.255.0 . ip daddr & 255.255.255.0 \
counter
3. Account traffic to each host per user:
flow skuid . ip daddr \
counter
4. Account traffic for each combination of source address and TCP flags:
flow ip saddr . tcp flags \
counter
The resulting set content after a Xmas-scan look like this:
{
192.168.122.1 . fin | psh | urg : counter packets 1001 bytes 40040,
192.168.122.1 . ack : counter packets 74 bytes 3848,
192.168.122.1 . psh | ack : counter packets 35 bytes 3144
}
In the future the "expressions attached to elements" will be extended
to also support user created non-stateful expressions to allow to
efficiently select beween a set of parameter sets, f.i. a set of log
statements with different prefixes based on the interface, which currently
require one rule each. This will most likely have to wait until the next
kernel version though.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs update from Al Viro:
"Part one:
- struct filename-related cleanups
- saner iov_iter_init() replacements (and switching the syscalls to
use of those)
- ntfs switch to ->write_iter() (Anton)
- aio cleanups and splitting iocb into common and async parts
(Christoph)
- assorted fixes (me, bfields, Andrew Elble)
There's a lot more, including the completion of switchover to
->{read,write}_iter(), d_inode/d_backing_inode annotations, f_flags
race fixes, etc, but that goes after #for-davem merge. David has
pulled it, and once it's in I'll send the next vfs pull request"
* 'for-linus-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (35 commits)
sg_start_req(): use import_iovec()
sg_start_req(): make sure that there's not too many elements in iovec
blk_rq_map_user(): use import_single_range()
sg_io(): use import_iovec()
process_vm_access: switch to {compat_,}import_iovec()
switch keyctl_instantiate_key_common() to iov_iter
switch {compat_,}do_readv_writev() to {compat_,}import_iovec()
aio_setup_vectored_rw(): switch to {compat_,}import_iovec()
vmsplice_to_user(): switch to import_iovec()
kill aio_setup_single_vector()
aio: simplify arguments of aio_setup_..._rw()
aio: lift iov_iter_init() into aio_setup_..._rw()
lift iov_iter into {compat_,}do_readv_writev()
NFS: fix BUG() crash in notify_change() with patch to chown_common()
dcache: return -ESTALE not -EBUSY on distributed fs race
NTFS: Version 2.1.32 - Update file write from aio_write to write_iter.
VFS: Add iov_iter_fault_in_multipages_readable()
drop bogus check in file_open_root()
switch security_inode_getattr() to struct path *
constify tomoyo_realpath_from_path()
...
|
|
The dwmac-socfpga.c conflict was a case of a bug fix overlapping
changes in net-next to handle an error pointer differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"Some clean ups and small fixes, but the biggest change is the addition
of the TRACE_DEFINE_ENUM() macro that can be used by tracepoints.
Tracepoints have helper functions for the TP_printk() called
__print_symbolic() and __print_flags() that lets a numeric number be
displayed as a a human comprehensible text. What is placed in the
TP_printk() is also shown in the tracepoint format file such that user
space tools like perf and trace-cmd can parse the binary data and
express the values too. Unfortunately, the way the TRACE_EVENT()
macro works, anything placed in the TP_printk() will be shown pretty
much exactly as is. The problem arises when enums are used. That's
because unlike macros, enums will not be changed into their values by
the C pre-processor. Thus, the enum string is exported to the format
file, and this makes it useless for user space tools.
The TRACE_DEFINE_ENUM() solves this by converting the enum strings in
the TP_printk() format into their number, and that is what is shown to
user space. For example, the tracepoint tlb_flush currently has this
in its format file:
__print_symbolic(REC->reason,
{ TLB_FLUSH_ON_TASK_SWITCH, "flush on task switch" },
{ TLB_REMOTE_SHOOTDOWN, "remote shootdown" },
{ TLB_LOCAL_SHOOTDOWN, "local shootdown" },
{ TLB_LOCAL_MM_SHOOTDOWN, "local mm shootdown" })
After adding:
TRACE_DEFINE_ENUM(TLB_FLUSH_ON_TASK_SWITCH);
TRACE_DEFINE_ENUM(TLB_REMOTE_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_MM_SHOOTDOWN);
Its format file will contain this:
__print_symbolic(REC->reason,
{ 0, "flush on task switch" },
{ 1, "remote shootdown" },
{ 2, "local shootdown" },
{ 3, "local mm shootdown" })"
* tag 'trace-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (27 commits)
tracing: Add enum_map file to show enums that have been mapped
writeback: Export enums used by tracepoint to user space
v4l: Export enums used by tracepoints to user space
SUNRPC: Export enums in tracepoints to user space
mm: tracing: Export enums in tracepoints to user space
irq/tracing: Export enums in tracepoints to user space
f2fs: Export the enums in the tracepoints to userspace
net/9p/tracing: Export enums in tracepoints to userspace
x86/tlb/trace: Export enums in used by tlb_flush tracepoint
tracing/samples: Update the trace-event-sample.h with TRACE_DEFINE_ENUM()
tracing: Allow for modules to convert their enums to values
tracing: Add TRACE_DEFINE_ENUM() macro to map enums to their values
tracing: Update trace-event-sample with TRACE_SYSTEM_VAR documentation
tracing: Give system name a pointer
brcmsmac: Move each system tracepoints to their own header
iwlwifi: Move each system tracepoints to their own header
mac80211: Move message tracepoints to their own header
tracing: Add TRACE_SYSTEM_VAR to xhci-hcd
tracing: Add TRACE_SYSTEM_VAR to kvm-s390
tracing: Add TRACE_SYSTEM_VAR to intel-sst
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Al Viro says:
====================
netdev-related stuff in vfs.git
There are several commits sitting in vfs.git that probably ought to go in
via net-next.git. First of all, there's merge with vfs.git#iocb - that's
Christoph's aio rework, which has triggered conflicts with the ->sendmsg()
and ->recvmsg() patches a while ago. It's not so much Christoph's stuff
that ought to be in net-next, as (pretty simple) conflict resolution on merge.
The next chunk is switch to {compat_,}import_iovec/import_single_range - new
safer primitives for initializing iov_iter. The primitives themselves come
from vfs/git#iov_iter (and they are used quite a lot in vfs part of queue),
conversion of net/socket.c syscalls belongs in net-next, IMO. Next there's
afs and rxrpc stuff from dhowells. And then there's sanitizing kernel_sendmsg
et.al. + missing inlined helper for "how much data is left in msg->msg_iter" -
this stuff is used in e.g. cifs stuff, but it belongs in net-next.
That pile is pullable from
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs.git for-davem
I'll post the individual patches in there in followups; could you take a look
and tell if everything in there is OK with you?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using a timer wheel for timewait sockets was nice ~15 years ago when
memory was expensive and machines had a single processor.
This does not scale, code is ugly and source of huge latencies
(Typically 30 ms have been seen, cpus spinning on death_lock spinlock.)
We can afford to use an extra 64 bytes per timewait sock and spread
timewait load to all cpus to have better behavior.
Tested:
On following test, /proc/sys/net/ipv4/tcp_tw_recycle is set to 1
on the target (lpaa24)
Before patch :
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
419594
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
437171
While test is running, we can observe 25 or even 33 ms latencies.
lpaa24:~# ping -c 1000 -i 0.02 -qn lpaa23
...
1000 packets transmitted, 1000 received, 0% packet loss, time 20601ms
rtt min/avg/max/mdev = 0.020/0.217/25.771/1.535 ms, pipe 2
lpaa24:~# ping -c 1000 -i 0.02 -qn lpaa23
...
1000 packets transmitted, 1000 received, 0% packet loss, time 20702ms
rtt min/avg/max/mdev = 0.019/0.183/33.761/1.441 ms, pipe 2
After patch :
About 90% increase of throughput :
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
810442
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
800992
And latencies are kept to minimal values during this load, even
if network utilization is 90% higher :
lpaa24:~# ping -c 1000 -i 0.02 -qn lpaa23
...
1000 packets transmitted, 1000 received, 0% packet loss, time 19991ms
rtt min/avg/max/mdev = 0.023/0.064/0.360/0.042 ms
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The printed values are all of type unsigned integer, therefore use
%u instead of %d. Otherwise an user can face negative values.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The printed values are all of type unsigned integer, therefore use
%u instead of %d. Otherwise an user can face negative values.
Fixes:
$ cat /proc/net/netfilter/nfnetlink_queue
0 29508 278 2 65531 0 2004213241 -2129885586 1
1 -27747 0 2 65531 0 0 0 1
2 -27748 0 2 65531 0 0 0 1
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netlink portid is an unsigned integer, use this type
also in netfilter.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
portid is an unsigned integer. Fix urelease_work to
match all other portid user in the kernel.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's an example net/netfilter/nft_expr_template.c example file in tree that
got out of sync along time, remove it.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
|
|
Support instantiating stateful expressions based on a template that
are associated with dynamically created set entries. The expressions
are evaluated when adding or updating the set element.
This allows to maintain per flow state using the existing set
infrastructure and expression types, with arbitrary definitions of
a flow.
Usage is currently restricted to anonymous sets, meaning only a single
binding can exist, since the desired semantics of multiple independant
bindings haven't been defined so far.
Examples (userspace syntax is still WIP):
1. Limit the rate of new SSH connections per host, similar to iptables
hashlimit:
flow ip saddr timeout 60s \
limit 10/second \
accept
2. Account network traffic between each set of /24 networks:
flow ip saddr & 255.255.255.0 . ip daddr & 255.255.255.0 \
counter
3. Account traffic to each host per user:
flow skuid . ip daddr \
counter
4. Account traffic for each combination of source address and TCP flags:
flow ip saddr . tcp flags \
counter
The resulting set content after a Xmas-scan look like this:
{
192.168.122.1 . fin | psh | urg : counter packets 1001 bytes 40040,
192.168.122.1 . ack : counter packets 74 bytes 3848,
192.168.122.1 . psh | ack : counter packets 35 bytes 3144
}
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add a set flag to indicate that the set is used as a state table and
contains expressions for evaluation. This operation is mutually
exclusive with the mapping operation, so sets specifying both are
rejected. The lookup expression also rejects binding to state tables
since it only deals with loopup and map operations.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add a flag to mark stateful expressions.
This is used for dynamic expression instanstiation to limit the usable
expressions. Strictly speaking only the dynset expression can not be
used in order to avoid recursion, but since dynamically instantiating
non-stateful expressions will simply create an identical copy, which
behaves no differently than the original, this limits to expressions
where it actually makes sense to dynamically instantiate them.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Preparation to attach expressions to set elements: add a set extension
type to hold an expression and dump the expression information with the
set element.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add helper functions for initializing, cloning, dumping and destroying
a single expression that is not part of a rule.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Since retransmitted segments are not used for RTT estimation, previously
SACKed segments present in the rtx queue are used. This estimation can be
several times larger than the actual RTT. When a cumulative ack covers both
previously SACKed and retransmitted segments, CC may thus get a bogus RTT.
Such segments previously had an RTT estimation in tcp_sacktag_one(), so it
seems reasonable to not reuse them in tcp_clean_rtx_queue() at all.
Afaik, this has had no effect on SRTT/RTO because of Karn's check.
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even if we make use of classifier and actions from the egress
path, we're going into handle_ing() executing additional code
on a per-packet cost for ingress qdisc, just to realize that
nothing is attached on ingress.
Instead, this can just be blinded out as a no-op entirely with
the use of a static key. On input fast-path, we already make
use of static keys in various places, e.g. skb time stamping,
in RPS, etc. It makes sense to not waste time when we're assured
that no ingress qdisc is attached anywhere.
Enabling/disabling of that code path is being done via two
helpers, namely net_{inc,dec}_ingress_queue(), that are being
invoked under RTNL mutex when a ingress qdisc is being either
initialized or destructed.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes sets to support variable sized set element keys / data
up to 64 bytes each by using variable sized set extensions. This allows
to use concatenations with bigger data items suchs as IPv6 addresses.
As a side effect, small keys/data now don't require the full 16 bytes
of struct nft_data anymore but just the space they need.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add a size argument to nft_data_init() and pass in the available space.
This will be used by the following patches to support variable sized
set element data.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Switch the nf_tables registers from 128 bit addressing to 32 bit
addressing to support so called concatenations, where multiple values
can be concatenated over multiple registers for O(1) exact matches of
multiple dimensions using sets.
The old register values are mapped to areas of 128 bits for compatibility.
When dumping register numbers, values are expressed using the old values
if they refer to the beginning of a 128 bit area for compatibility.
To support concatenations, register loads of less than a full 32 bit
value need to be padded. This mainly affects the payload and exthdr
expressions, which both unconditionally zero the last word before
copying the data.
Userspace fully passes the testsuite using both old and new register
addressing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add helper functions to parse and dump register values in netlink attributes.
These helpers will later be changed to take care of translation between the
old 128 bit and the new 32 bit register numbers.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Simple conversion to use u32 pointers to the beginning of the data
area to keep follow up patches smaller.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Only needlessly complicates things due to requiring specific argument
types. Use memcmp directly.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Simple conversion to use u32 pointers to the beginning of the registers
to keep follow up patches smaller.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Replace the array of registers passed to expressions by a struct nft_regs,
containing the verdict as a seperate member, which aliases to the
NFT_REG_VERDICT register.
This is needed to seperate the verdict from the data registers completely,
so their size can be changed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Change nft_validate_input_register() to not only validate the input
register number, but also the length of the load, and rename it to
nft_validate_register_load() to reflect that change.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
All users of nft_validate_register_store() first invoke
nft_validate_output_register(). There is in fact no use for using it
on its own, so simplify the code by folding the functionality into
nft_validate_register_store() and kill it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
In preparation of validating the length of a register store, use
nft_validate_register_store() in nft_lookup instead of open coding the
validation.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The existing name is ambiguous, data is loaded as well when we read from
a register. Rename to nft_validate_register_store() for clarity and
consistency with the upcoming patch to introduce its counterpart,
nft_validate_register_load().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
For values spanning multiple registers, we need to validate that enough
space is available from the destination register onwards. Add a len
argument to nft_validate_data_load() and consolidate the existing length
validations in preparation of that.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-04-11
This series contains updates to iflink, ixgbe and ixgbevf.
The entire set of changes come from Vlad Zolotarov to ultimately add
the ethtool ops to VF driver to allow querying the RSS indirection table
and RSS random key.
Currently we support only 82599 and x540 devices. On those devices, VFs
share the RSS redirection table and hash key with a PF. Letting the VF
query this information may introduce some security risks, therefore this
feature will be disabled by default.
The new netdev op allows a system administrator to change the default
behaviour with "ip link set" command. The relevant iproute2 patch has
already been sent and awaits for this series upstream.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Also convert the spinlock to a mutex.
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
udp_config.local_udp_port is be16. And iproute2 passes
network order for FOU_ATTR_PORT.
This doesn't fix any bug, just for consistency.
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not a big deal, just for corretness.
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes the following harmless warning:
./ip/ip fou del port 7777
[ 122.907516] udp_del_offload: didn't find offload for port 7777
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With recent adoption of skc_cookie in struct sock_common,
struct tcp_timewait_sock size increased from 192 to 200 bytes
on 64bit arches. SLAB rounds then to 256 bytes.
It is time to drop SLAB_HWCACHE_ALIGN constraint for twsk_slab.
This saves about 12 MB of memory on typical configuration reaching
262144 timewait sockets, and has no noticeable impact on performance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
There isn't much left, but we have
* new mac80211 internal software queue to allow drivers to have
shorter hardware queues and pull on-demand
* use rhashtable for mac80211 station table
* minstrel rate control debug improvements and some refactoring
* fix noisy message about TX power reduction
* fix continuous message printing and activity if CRDA doesn't respond
* fix VHT-related capabilities with "iw connect" or "iwconfig ..."
* fix Kconfig for cfg80211 wireless extensions compatibility
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All places outside of core VFS that checked ->read and ->write for being NULL or
called the methods directly are gone now, so NULL {read,write} with non-NULL
{read,write}_iter will do the right thing in all cases.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
it's almost always equal to current_fsuid(), but there's an exception -
if the first writeback fid is opened by non-root *and* that happens before
root has done any lookups in /, we end up doing attach for root. The
current code leaves the resulting FID owned by root from the server POV
and by non-root from the client one. Unfortunately, it means that e.g.
massive dcache eviction will leave that user buggered - they'll end
up redoing walks from / *and* picking that FID every time. As soon as
they try to create something, the things will get nasty.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
... and make it loop
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
... and make it loop until it's done
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
... and have get_user_pages_fast() mapping fewer pages than requested
to generate a short read/write.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
|
|
convert open-coded instances
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
|
|
it's equal to iov_iter_count(&msg->msg_iter) in all cases
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Add configuration setting for drivers to allow/block an RSS Redirection
Table and a Hash Key querying for discrete VFs.
On some devices VF share the mentioned above information with PF and
querying it may adduce a theoretical security risk. We want to let a
system administrator to decide if he/she wants to take this risk or not.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-04-09
We've had enough new patches during the past week (especially from
Marcel) that it'd be good to still get these queued for 4.1.
The majority of the changes are from Marcel with lots of cleanup &
refactoring patches for the HCI UART driver. Marcel also split out some
Broadcom & Intel vendor specific functionality into two new btintel &
btbcm modules.
In addition to the HCI driver changes there's the completion of our
local OOB data interface for pairing, added support for requesting
remote LE features when connecting, as well as a couple of minor fixes
for mac802154.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lookup key for tcp_md5_do_lookup() has to be taken
from addr_sk, not sk (which can be the listener)
Fixes: fd3a154a00fb ("tcp: md5: get rid of tcp_v[46]_reqsk_md5_lookup()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an FDB entry is added or deleted the information about VLAN
is not passed to listening applications like 'bridge monitor fdb'.
With this patch VLAN ID is passed if it was set in the original
netlink message.
Also remove an unused bdev variable.
Signed-off-by: Hubert Sokolowski <hubert.sokolowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I noticed tcpdump was giving funky timestamps for locally
generated SYNACK messages on loopback interface.
11:42:46.938990 IP 127.0.0.1.48245 > 127.0.0.2.23850: S
945476042:945476042(0) win 43690 <mss 65495,nop,nop,sackOK,nop,wscale 7>
20:28:58.502209 IP 127.0.0.2.23850 > 127.0.0.1.48245: S
3160535375:3160535375(0) ack 945476043 win 43690 <mss
65495,nop,nop,sackOK,nop,wscale 7>
This is because we need to clear skb->tstamp before
entering lower stack, otherwise net_timestamp_check()
does not set skb->tstamp.
Fixes: 7faee5c0d514 ("tcp: remove TCP_SKB_CB(skb)->when")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
handle_offloads() calls skb_reset_inner_headers() to store
the layer pointers to the encapsulated packet. However, we
currently push the vlag tag (if there is one) onto the packet
afterwards. This changes the MAC header for the encapsulated
packet but it is not reflected in skb->inner_mac_header, which
breaks GSO and drivers which attempt to use this for encapsulation
offloads.
Fixes: 1eaa8178 ("vxlan: Add tx-vlan offload support.")
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next tree.
They are:
* nf_tables set timeout infrastructure from Patrick Mchardy.
1) Add support for set timeout support.
2) Add support for set element timeouts using the new set extension
infrastructure.
4) Add garbage collection helper functions to get rid of stale elements.
Elements are accumulated in a batch that are asynchronously released
via RCU when the batch is full.
5) Add garbage collection synchronization helpers. This introduces a new
element busy bit to address concurrent access from the netlink API and the
garbage collector.
5) Add timeout support for the nft_hash set implementation. The garbage
collector peridically checks for stale elements from the workqueue.
* iptables/nftables cgroup fixes:
6) Ignore non full-socket objects from the input path, otherwise cgroup
match may crash, from Daniel Borkmann.
7) Fix cgroup in nf_tables.
8) Save some cycles from xt_socket by skipping packet header parsing when
skb->sk is already set because of early demux. Also from Daniel.
* br_netfilter updates from Florian Westphal.
9) Save frag_max_size and restore it from the forward path too.
10) Use a per-cpu area to restore the original source MAC address when traffic
is DNAT'ed.
11) Add helper functions to access physical devices.
12) Use these new physdev helper function from xt_physdev.
13) Add another nf_bridge_info_get() helper function to fetch the br_netfilter
state information.
14) Annotate original layer 2 protocol number in nf_bridge info, instead of
using kludgy flags.
15) Also annotate the pkttype mangling when the packet travels back and forth
from the IP to the bridge layer, instead of using a flag.
* More nf_tables set enhancement from Patrick:
16) Fix possible usage of set variant that doesn't support timeouts.
17) Avoid spurious "set is full" errors from Netlink API when there are pending
stale elements scheduled to be released.
18) Restrict loop checks to set maps.
19) Add support for dynamic set updates from the packet path.
20) Add support to store optional user data (eg. comments) per set element.
BTW, I have also pulled net-next into nf-next to anticipate the conflict
resolution between your okfn() signature changes and Florian's br_netfilter
updates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2015-04-09
1) Prohibit the use/abuse of the xfrm netlink interface on
32/64 bit compatibility tasks. We need a full compat
layer before we can allow this. From Fan Du.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2015-04-09
1) We dereferenced the xfrm outer_mode too early, larval
SAs don't have it set. Move the dereference of the
outer mode below the larval SA check to fix it.
From Alexey Dobriyan.
2) Fix vti6 tunnel uninit on namespace crosssing.
From Yao Xiwei.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When establishing a Bluetooth LE connection, read the remote used
features mask to determine which features are supported. This was
not really needed with Bluetooth 4.0, but since Bluetooth 4.1 and
also 4.2 have introduced new optional features, this becomes more
important.
This works the same as with BR/EDR where the connection enters the
BT_CONFIG stage and hci_connect_cfm call is delayed until the remote
features have been retrieved. Only after successfully receiving the
remote features, the connection enters the BT_CONNECTED state.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
For kernel_sendmsg() that eliminates the need to play with setfs();
for kernel_recvmsg() it does *not* - a couple of callers are using
it with non-NULL ->msg_control, which would be treated as userland
address on recvmsg side of things.
In all cases we are really setting a kvec-backed iov_iter, though.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
trivial conflict in net/socket.c and non-trivial one in crypto -
that one had evaded aio_complete() removal.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
FastOpen requests are not like other regular request sockets.
They do not yet use rsk_timer : tcp_fastopen_queue_check()
simply manually removes one expired request from fastopenq->rskq_rst
list.
Therefore, tcp_check_req() must not call mod_timer_pending(),
otherwise we crash because rsk_timer was not initialized.
Fixes: fa76ce7328b ("inet: get rid of central tcp/dccp listener timer")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC: 4.1 pull request
This is the NFC pull request for 4.1.
This is a shorter one than usual, as the Intel Field Peak NFC
driver could not make it in time.
We have:
- A new driver for NXP NCI based chipsets, like e.g. the NPC100 or
the PN7150. It currently only supports an i2c physical layer, but
could easily be extended to work on top of e.g. SPI.
This driver also includes support for user space triggered firmware
updates.
- A few minor st21nfc[ab] fixes, cleanups, and comments improvements.
- A pn533 error return fix.
- A few NFC related logs formatting cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
const __read_mostly is a senseless combination. If something
is already const it cannot be __read_mostly. Remove the bogus
__read_mostly in the fou driver.
This fixes section conflicts with LTO.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
More recent GCC warns about two kinds of switch statement uses:
1) Switching on an enumeration, but not having an explicit case
statement for all members of the enumeration. To show the
compiler this is intentional, we simply add a default case
with nothing more than a break statement.
2) Switching on a boolean value. I think this warning is dumb
but nevertheless you get it wholesale with -Wswitch.
This patch cures all such warnings in netfilter.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
If a determined set of concurrent senders keep the send queue full,
we can loop forever inside rds_send_xmit. This fix has two parts.
First we are dropping out of the while(1) loop after we've processed a
large batch of messages.
Second we add a generation number that gets bumped each time the
xmit bit lock is acquired. If someone else has jumped in and
made progress in the queue, we skip our goto restart.
Original patch by Chris Mason.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Passive connections were added for the case where one loopback IB
connection between identical addresses needs another connection to store
the second QP. Unfortunately, they were also created in the case where
the addesses differ and we already have both QPs.
This lead to a message reordering bug.
- two different IB interfaces and addresses on a machine: A B
- traffic is sent from A to B
- connection from A-B is created, connect request sent
- listening accepts connect request, B-A is created
- traffic flows, next_rx is incremented
- unacked messages exist on the retrans list
- connection A-B is shut down, new connect request sent
- listen sees existing loopback B-A, creates new passive B-A
- retrans messages are sent and delivered because of 0 next_rx
The problem is that the second connection request saw the previously
existing parent connection. Instead of using it, and using the existing
next_rx_seq state for the traffic between those IPs, it mistakenly
thought that it had to create a passive connection.
We fix this by only using passive connections in the special case where
laddr and faddr match. In this case we'll only ever have one parent
sending connection requests and one passive connection created as the
listening path sees the existing parent connection which initiated the
request.
Original patch by Zach Brown
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resolve conflicts between 5888b93 ("Merge branch 'nf-hook-compress'") and
Florian Westphal br_netfilter works.
Conflicts:
net/bridge/br_netfilter.c
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Fixes: 79b16aadea32cce ("udp_tunnel: Pass UDP socket down through udp_tunnel{, 6}_xmit_skb().")
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The socket parameter might legally be NULL, thus sock_net is sometimes
causing a NULL pointer dereference. Using net_device pointer in dst_entry
is more reliable.
Fixes: b6a7719aedd7e5c ("ipv4: hash net ptr into fragmentation bucket selection")
Reported-by: Rick Jones <rick.jones2@hp.com>
Cc: Rick Jones <rick.jones2@hp.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an userdata set extension and allow the user to attach arbitrary
data to set elements. This is intended to hold TLV encoded data like
comments or DNS annotations that have no meaning to the kernel.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add a new "dynset" expression for dynamic set updates.
A new set op ->update() is added which, for non existant elements,
invokes an initialization callback and inserts the new element.
For both new or existing elements the extenstion pointer is returned
to the caller to optionally perform timer updates or other actions.
Element removal is not supported so far, however that seems to be a
rather exotic need and can be added later on.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Currently a set binding is assumed to be related to a lookup and, in
case of maps, a data load.
In order to use bindings for set updates, the loop detection checks
must be restricted to map operations only. Add a flags member to the
binding struct to hold the set "action" flags such as NFT_SET_MAP,
and perform loop detection based on these.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Use atomic operations for the element count to avoid races with async
updates.
To properly handle the transactional semantics during netlink updates,
deleted but not yet committed elements are accounted for seperately and
are treated as being already removed. This means for the duration of
a netlink transaction, the limit might be exceeded by the amount of
elements deleted. Set implementations must be prepared to handle this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The NFT_SET_TIMEOUT flag is ignore in nft_select_set_ops, which may
lead to selection of a set implementation that doesn't actually
support timeouts.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
nf_bridge_info->mask is used for several things, for example to
remember if skb->pkt_type was set to OTHER_HOST.
For a bridge, OTHER_HOST is expected case. For ip forward its a non-starter
though -- routing expects PACKET_HOST.
Bridge netfilter thus changes OTHER_HOST to PACKET_HOST before hook
invocation and then un-does it after hook traversal.
This information is irrelevant outside of br_netfilter.
After this change, ->mask now only contains flags that need to be
known outside of br_netfilter in fast-path.
Future patch changes mask into a 2bit state field in sk_buff, so that
we can remove skb->nf_bridge pointer for good and consider all remaining
places that access nf_bridge info content a not-so fastpath.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
->mask is a bit info field that mixes various use cases.
In particular, we have flags that are mutually exlusive, and flags that
are only used within br_netfilter while others need to be exposed to
other parts of the kernel.
Remove BRNF_8021Q/PPPoE flags. They're mutually exclusive and only
needed within br_netfilter context.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Don't access skb->nf_bridge directly, this pointer will be removed soon.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Avoid skb->nf_bridge accesses where possible.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
right now we store this in the nf_bridge_info struct, accessible
via skb->nf_bridge. This patch prepares removal of this pointer from skb:
Instead of using skb->nf_bridge->x, we use helpers to obtain the in/out
device (or ifindexes).
Followup patches to netfilter will then allow nf_bridge_info to be
obtained by a call into the br_netfilter core, rather than keeping a
pointer to it in sk_buff.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
br_netfilter maintains an extra state, nf_bridge_info, which is attached
to skb via skb->nf_bridge pointer.
Amongst other things we use skb->nf_bridge->data to store the original
mac header for every processed skb.
This is required for ip refragmentation when using conntrack
on top of bridge, because ip_fragment doesn't copy it from original skb.
However there is no need anymore to do this unconditionally.
Move this to the one place where its needed -- when br_netfilter calls
ip_fragment().
Also switch to percpu storage for this so we can handle fragmenting
without accessing nf_bridge meta data.
Only user left is neigh resolution when DNAT is detected, to hold
the original source mac address (neigh resolution builds new mac header
using bridge mac), so rename ->data and reduce its size to whats needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
match
Currently in xt_socket, we take advantage of early demuxed sockets
since commit 00028aa37098 ("netfilter: xt_socket: use IP early demux")
in order to avoid a second socket lookup in the fast path, but we
only make partial use of this:
We still unnecessarily parse headers, extract proto, {s,d}addr and
{s,d}ports from the skb data, accessing possible conntrack information,
etc even though we were not even calling into the socket lookup via
xt_socket_get_sock_{v4,v6}() due to skb->sk hit, meaning those cycles
can be spared.
After this patch, we only proceed the slower, manual lookup path
when we have a skb->sk miss, thus time to match verdict for early
demuxed sockets will improve further, which might be i.e. interesting
for use cases such as mentioned in 681f130f39e1 ("netfilter: xt_socket:
add XT_SOCKET_NOWILDCARD flag").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The change to only export WEXT symbols when required could break
the build if CONFIG_CFG80211_WEXT was explicitly disabled while
a driver like orinoco selected it.
Fix this by hiding the symbol when it's required so it can't be
disabled in that case.
Fixes: 2afe38d15cee ("cfg80211-wext: export symbols only when needed")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fast Open has been using an experimental option with a magic number
(RFC6994). This patch makes the client by default use the RFC7413
option (34) to get and send Fast Open cookies. This patch makes
the client solicit cookies from a given server first with the
RFC7413 option. If that fails to elicit a cookie, then it tries
the RFC6994 experimental option. If that also fails, it uses the
RFC7413 option on all subsequent connect attempts. If the server
returns a Fast Open cookie then the client caches the form of the
option that successfully elicited a cookie, and uses that form on
later connects when it presents that cookie.
The idea is to gradually obsolete the use of experimental options as
the servers and clients upgrade, while keeping the interoperability
meanwhile.
Signed-off-by: Daniel Lee <Longinus00@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fast Open has been using the experimental option with a magic number
(RFC6994) to request and grant Fast Open cookies. This patch enables
the server to support the official IANA option 34 in RFC7413 in
addition.
The change has passed all existing Fast Open tests with both
old and new options at Google.
Signed-off-by: Daniel Lee <Longinus00@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
instances
Fixes byte backlog accounting for the first of two chained netem instances.
Bytes backlog reported now corresponds to the number of queued packets.
When two netem instances are chained, for instance to apply rate and queue
limitation followed by packet delay, the number of backlogged bytes reported
by the first netem instance is wrong. It reports the sum of bytes in the queues
of the first and second netem. The first netem reports the correct number of
backlogged packets but not bytes. This is shown in the example below.
Consider a chain of two netem schedulers created using the following commands:
$ tc -s qdisc replace dev veth2 root handle 1:0 netem rate 10000kbit limit 100
$ tc -s qdisc add dev veth2 parent 1:0 handle 2: netem delay 50ms
Start an iperf session to send packets out on the specified interface and
monitor the backlog using tc:
$ tc -s qdisc show dev veth2
Output using unpatched netem:
qdisc netem 1: root refcnt 2 limit 100 rate 10000Kbit
Sent 98422639 bytes 65434 pkt (dropped 123, overlimits 0 requeues 0)
backlog 172694b 73p requeues 0
qdisc netem 2: parent 1: limit 1000 delay 50.0ms
Sent 98422639 bytes 65434 pkt (dropped 0, overlimits 0 requeues 0)
backlog 63588b 42p requeues 0
The interface used to produce this output has an MTU of 1500. The output for
backlogged bytes behind netem 1 is 172694b. This value is not correct. Consider
the total number of sent bytes and packets. By dividing the number of sent
bytes by the number of sent packets, we get an average packet size of ~=1504.
If we divide the number of backlogged bytes by packets, we get ~=2365. This is
due to the first netem incorrectly counting the 63588b which are in netem 2's
queue as being in its own queue. To verify this is the case, we subtract them
from the reported value and divide by the number of packets as follows:
172694 - 63588 = 109106 bytes actualled backlogged in netem 1
109106 / 73 packets ~= 1494 bytes (which matches our MTU)
The root cause is that the byte accounting is not done at the
same time with packet accounting. The solution is to update the backlog value
every time the packet queue is updated.
Signed-off-by: Joseph D Beshay <joseph.beshay@utdallas.edu>
Acked-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Read Local Out Of Band Extended Data mgmt command is specified to
return the SSP values when given a BR/EDR address type as input
parameter. The returned values may include either the 192-bit variants
of C and R, or their 256-bit variants, or both, depending on the status
of Secure Connections and Secure Connections Only modes. If SSP is not
enabled the command will only return the Class of Device value (like it
has done so far).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Which this patch, it's possible to dump the list of ids allocated for peer
netns.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With this patch, netns ids that are created and deleted are advertised into the
group RTNLGRP_NSID.
Because callers of rtnl_net_notifyid() already know the id of the peer, there is
no need to call __peernet2id() in rtnl_net_fill().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to initialize err, it will be overridden by the value of nlmsg_parse().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
That was we can make sure the output path of ipv4/ipv6 operate on
the UDP socket rather than whatever random thing happens to be in
skb->sk.
Based upon a patch by Jiri Pirko.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
|
|
On the output paths in particular, we have to sometimes deal with two
socket contexts. First, and usually skb->sk, is the local socket that
generated the frame.
And second, is potentially the socket used to control a tunneling
socket, such as one the encapsulates using UDP.
We do not want to disassociate skb->sk when encapsulating in order
to fix this, because that would break socket memory accounting.
The most extreme case where this can cause huge problems is an
AF_PACKET socket transmitting over a vxlan device. We hit code
paths doing checks that assume they are dealing with an ipv4
socket, but are actually operating upon the AF_PACKET one.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is currently always set to NULL, but nf_queue is adjusted to be
prepared for it being set to a real socket by taking and releasing a
reference to that socket when necessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hci_recv_stream_fragment function should have never been introduced
in the first place. The Bluetooth core does not need to know anything
about the HCI transport protocol.
With all transport protocol specific detailed moved back into the
drivers where they belong (mainly generic USB and UART drivers), this
function can now be removed.
This reduces the size of hci_dev structure and also removes an exported
symbol from the Bluetooth core module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The data pointer provided to hci_recv_stream_fragment function should
have been marked const. The function has no business in modifying the
original data. So fix this now.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
